Power Base-2 & 800CSL Amplifier Service Manual

Specifications

Unless noted otherwise, all specifications are based on driving an 8 ohm load per channel, both channels driven, the sensitivity switch in the 26dB position, the AC supply is 120VAC at 60Hz. Crown specifications are guaranteed through the warranty period (normally 3 years). Because our testing methods are more strin- gent than our published specifications, every Crown amplifier will exceed its published specifications.

POWER

Power

8 Ohm Stereo—320W/Ch

4 Ohm Stereo—400W/Ch

8 Ohm Bridge Mono—965W

4 Ohm Parallel Mono—680W

2 Ohm Parallel Mono—955W

Load Impedances: Rated for 16, 8, 4, and 2 (parallel mono only) Ohm operation; safe with all types of loads, even totally reactive loads.

AC Mains: 120VAC at 60 Hz with standard 3 wire grounded 15A connector with single voltage trans- former and fan for North American units; 100VAC, 120VAC, 220VAC, and 240VAC at 50 or 60 Hz when equipped with universal transformer, applicable fan, and other applicable hardware with country specific power cord. Note that at 50 Hz fan speed is reduced.

PERFORMANCE

Frequency Response: ±0.1dB from 20 Hz to 20 kHz at 1 Watt.

Phase Response: ±10° from 10 Hz to 20 kHz at 1 Watt.

Signal to Noise Ratio: Better than 105 dB (A-weighted) below max. average power from 20 Hz to 20 kHz.

Total Harmonic Distortion (THD): <0.05% from 20 Hz to 1 kHz, increasing linearly to 0.1% at 20 kHz at 170W.

I.M. Distortion: <0.05% from 10 milliwatts to 170W at 26 dB gain.

Slew Rate: >13V per microsecond.

Damping Factor: >1000 from 10 Hz to 400 Hz.

DC Offset: <10 millivolts.

Input Impedance: Nominally 20K ohms balanced; 10K ohms unbalanced.

Output Impedance: <10 milliohms in series with <2 microhenries.

Protection Systems: Output Device Emulation Protec- tion (ODEP) limits drive in the event of dangerous dynamic thermal conditions without interrupting power. Current limiting for shorted load protection. DC/LF and common mode output current Fault circuitry to mute audio. Delay of 4 seconds from turn on mutes amplifier to prevent dangerous turn-on transients. High voltage fuse in main transformer primary and low voltage fuse in fan primary. Slew rate limiting to prevent RF burn out.

MECHANICAL

Input Connectors: Balanced 1/4 inch phone jacks.

Output Connectors: Color-coded 5-way binding posts on 3/4 inch centers; spaced 3/4 inch apart.

Front Panel Controls: A rocker on/off power switch.

Back Panel Controls: A three-position switch which selects Stereo, Bridge-Mono, or Parallel-Mono mode; a two position input ground-lift switch, and level con- trols for each channel.

Internal Controls: A three-position switch selects 0.775V, 1.4V, or 26 dB voltage gain input sensitivity (all units manufactured with D 7911-7 main module or later; earlier models only allowed for 0.775V or 26 dB gain).

Indicators: Red Enable indicator shows on/off status of low-voltage power supply.

Construction: Black splatter-coat steel chassis with specially designed flow-through ventilation system.

Mounting: Standard EIA 310 front-panel rack mount with supports for supplemental rear corner mounting.

Dimensions: 19 inches wide, 3.5 inches high, 16 inches deep behind front mounting surface.

Weight: 32 lbs.

6

Page 5 Page 7
Page 6
Image 6
Crown Audio 800CSL service manual Specifications, Power, Performance, Mechanical
Page 5 Page 7

800CSL specifications

Crown Audio has long been a respected name in professional audio equipment, and the 800CSL amplifiers are a testament to their unwavering commitment to quality and performance. Designed for professional sound reinforcement applications, the Crown 800CSL offers an impressive blend of power, reliability, and versatility, making it a popular choice among audio engineers and event coordinators.

At the heart of the Crown 800CSL is its robust power output. This amplifier delivers an impressive 800 watts per channel at 4 ohms, ensuring that it can drive even the most demanding speakers with ease. It features a Class D design, which not only maximizes efficiency, allowing for more power with less heat generation, but also contributes to a lightweight chassis that is easy to transport and install. This makes the 800CSL a versatile option for both permanent installations and mobile events.

One of the key technologies employed in the Crown 800CSL is its comprehensive built-in protection circuitry. This includes advanced short circuit protection, over-temperature protection, and current limiting. Such features ensure that the amplifier operates reliably in challenging conditions, reducing the risk of damage to both the amplifier and the connected speakers. The inclusion of a low-frequency filter further enhances performance, providing clean, powerful bass without distortion.

The Crown 800CSL also offers a range of connectivity options, including XLR and ΒΌ-inch inputs, making it compatible with a wide variety of audio sources. This flexibility, combined with user-friendly front panel controls, allows audio professionals to set up and adjust the system quickly and efficiently.

Additionally, the amplifier features a robust and compact design with a lightweight aluminum chassis. This not only contributes to its portability but also aids in heat dissipation, further enhancing performance during prolonged use. The included handles on the chassis make it easy to transport the unit between gigs, while its durable components ensure longevity.

In summary, the Crown Audio 800CSL stands out for its power, efficiency, and reliability. From its Class D amplification technology to its comprehensive protection features, this amplifier is designed to meet the needs of professionals in the audio industry. Whether for concerts, events, or installations, the 800CSL is poised to deliver exceptional sound quality and performance, making it a valuable addition to any audio toolkit.
Top Page Image Contents