Manuals / Crown Audio / Home Audio / Stereo Amplifier

Crown Audio S Series 2Setup, 2.6.3Bridge-MonoMode, S-Series Power Amplifiers, page

Models: S Series

1 28

Download 28 pages 21.36 Kb

Page 10

Image 10

2Setup

2.6.3Bridge-Mono Mode

Make sure the amplifier is turned off and the level controls are turned down before you wire the system.

Typical input and output wiring is shown in Figure 2.11.

INPUTS: Connect input wiring to CH 1.

OUTPUTS: Connect the speaker across the posi- tive (+) output terminals. Do not use the negative

(–)terminals when the amplifier is being oper- ated in Bridge-Mono mode. Refer to Section 2.5 for output connector pin assignments. Make sure the Mode switch is set to the “Bridge” posi- tion when operating in Bridge-Mono mode.

NOTE: Turn down (full CCW) the Channel 2 level control when operating the channel pair in Bridge-Mono mode, as the Channel 1 level control works both channels.

NOTE: Crown provides a reference of wiring pin assignments for commonly used connector types in the Crown Amplifier Application Guide available at www.crownaudio.com.

S-SeriesPower Amplifiers

Figure 2.11 Typical System Wiring, Bridge-Mono Mode

page 10

Operation Manual

Page 10

Image 10

Crown Audio S Series operation manual 2Setup, 2.6.3Bridge-MonoMode, S-Series Power Amplifiers, page

Contents

Some models may be exported under the name Amcron S-2 S-3S-Series WATCH FOR THESE SYMBOLS Important Safety InstructionsS-Series Power Amplifiers S Series amplifiers require Class 2 output wiringCrown International, Inc Safety Standardpage Family Name S-SeriesTroubleshooting Table of Contents2 Setup Specifications1 Welcome 1.1 Features1.2 How to Use This Manual S-Series Power Amplifiers2.1 Unpack Your Amplifier 2 Setup2.2 Install Your Amplifier S-Series Power AmplifiersS-Series Power Amplifiers 2.4Choose Input Wire and Connectors2 Setup Figure 2.3 Balanced Input Connector WiringS-Series Power Amplifiers 2.5 Choose Output Wire and Con- nectors2 Setup Figure 2.6 Neutrik Speakon Connector2 Setup 2.6 Wire Your System 2.6.1 Stereo Mode2.6.2 How to Parallel the Inputs S-Series Power AmplifiersS-Series Power Amplifiers 2Setup2.6.3Bridge-MonoMode page2.8 Connect to AC Mains 2.7 Input Sensitivity Switch2.9 Startup Procedure 2 SetupS-Series Power Amplifiers 3.1 Precautions3 Operation pageFigure Controls Indicators & Connectors 3.2 Controls, Indicators and ConnectorsS-Series Power Amplifiers 3 OperationReset Switch 3.3 Front Panel Controls and IndicatorsPower Switch Fault Indicators4.1.6 Power Circuit Breaker 4 Advanced Features and Options4.1.2 Fault 4.2 Advanced Features 4.2.1 Crown SST ModulesSST-4622 SST-SBSC-3632TSST-SBSC4632T SST-3632S-Series Power Amplifiers 4.2.2 Fault Monitoring4 Advanced Features and Options page4.3.4Optional 0.775 V Input Sensitivity Setting 4.3 Options 4.3.1 Accessories4.3.2 Alternate Output Connectors 4.3.3 Tamper-ResistantHole PlugsS-Series Power Amplifiers 5 Principles of Operationpage ERROR S-Series Power AmplifiersDiagram INPUTS Shown with Standard Input Module 5 Principles of OperationCONDITION Power indicator is off 6 TroubleshootingS-Series Power Amplifiers CONDITION Fault indicator is flashingS-Series Power Amplifiers 7 Specifications120 VAC, 60 Hz Units, Bridge mono mode Minimum Guaranteed Power8.2 US Service 8 Service8.1 International and Canada Service 8.2.1 Service at a US Service CenterITEMS EXCLUDED FROM THIS CROWN- WARRANTY 9 WarrantySUMMARY OF WARRANTY WARRANTY ALTERATIONSS-Series Power Amplifiers This page intentionally left blankpage This page intentionally left blank S-Series Power Amplifierspage S-Series Power Amplifiers PRODUCT RETURN INFORMATIONCrown Audio Factory Service Information PLEASE PRINT CLEARLY