3

Assembling

Your Tiller

WARNING

Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.

Be certain to check the clutch cable adjustment before operating the tiller.

NOTE: References to right or left side of the tiller are determined from behind the unit in the operating position.

To Remove Unit From Carton

•Remove staples, break glue on top flaps, or cut tape at carton end and peel along top flap to open carton.

•Remove loose parts included with unit (i.e., operator’s manual, etc.).

•Cut corners and lay carton down flat.

•Remove packing material.

•Roll or slide unit out of carton. Check carton thoroughly for loose parts.

•Extend control cable and lay on the floor. Be careful not to bend or kink control cable.

IMPORTANT: This unit is shipped without gasoline or oil in the engine. Be certain to service engine with gasoline and oil as instructed in the separate engine manual before operating your machine.

Loose Parts In Carton

•Depth Stake

•Handle Assembly

•Shift Rod

NOTE: All hardware needed for assembly is attached to the loose parts or the tiller.

Before Assembly

WARNING: Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.

Attaching Depth Stake

•Tip the tiller forward so it rests on front counterweight.

•Unthread the “T” knob from the top of the depth stake and remove the flat washer and hex bolt. Remove the hairpin clip from the clevis pin. See Figure 1.

•Raise the tine shield hinge flap assembly and insert the depth stake assembly in the slot (under the tine shield) and up through the tine shield assembly.

•Insert clevis pin through the tine shield and depth stake assemblies. Secure with hairpin clip.

•Insert a hex bolt into top hole of the depth stake assembly. Place flat washer on the hex bolt and thread “T” knob onto the hex bolt. Tighten securely.

See Figure 1.

•Tip the tiller back down so it rests on the tines.

Attaching Handle Assembly

•Remove top two bolts and flange lock nuts from handle mounting brackets, but do not remove the bottom bolt and nut. See Figure 2.

•Place handle assembly in position between the handle mounting brackets.

•Line up holes in handle with holes in bracket and secure with hardware previously removed.

Attaching Clutch Cable

Attach the clutch cable to the handle as follows: (be careful not to kink the cable)

Flat Washer Hex Bolt

 

T-Knob

Hairpin Clip

Clevis Pin

 

Depth Stake

Figure 1

 

Remove

Handle

Assembly

 

 

Handle

 

Bracket

Figure 2

•Remove threaded eyebolt and nut from the cable end.

•Route the clutch cable to the right side of the handle mounting brackets and underneath the handle.

•Push the cable through the hole in the center of the handle and snap in the plastic fitting. See Figure 3.

•Remove slot head screw, nut, and two flat washers from the clutch bail. See Figure 4.

•Fasten the threaded eyebolt onto bail by securing from top with slot head screw, flat washers and lock nut.

•Thread eyebolt and nut removed earlier into the internally threaded tube at the end of the cable. Thread engagement should be about 3/4”. Tighten nut against tube at end of cable. See Figure 4.

NOTE: Do not overtighten clutch cable. Too much tension may cause it to break.

WARNING: Be certain to check the clutch cable adjustment before operat- ing the tiller.

6

Page 5 Page 7
Page 6
Image 6
Cub Cadet 450 warranty Assembling Your Tiller
Page 5 Page 7

450 specifications

The Cub Cadet 450 is a versatile and highly efficient garden tractor that has earned a reputation for its performance and durability. Designed for both residential and light commercial use, this model is equipped with a range of features and technologies that cater to a variety of landscaping needs.

At the heart of the Cub Cadet 450 is a robust engine that delivers powerful performance. The tractor is equipped with a 450cc engine, providing ample power to tackle challenging mowing tasks and other yard work. This engine is designed to be fuel-efficient, reducing the number of refueling stops needed during larger projects.

One of the standout features of the Cub Cadet 450 is its innovative hydrostatic transmission. This technology allows for smooth, effortless operation by providing automatic speed and directional control. Operators can easily adjust their speed without having to shift gears, enabling a more comfortable mowing experience.

The Cub Cadet 450 comes with a cutting deck that is engineered for precision and durability. Available in various widths, the deck is designed with dual-blade systems that ensure a clean, even cut, even in thick grass. Additionally, the “deck wash” feature makes maintenance easy, allowing users to quickly clean the underside of the deck to prevent grass buildup.

Another significant aspect of the Cub Cadet 450 is its user-friendly design. The tractor features an ergonomic seating position, allowing for extended periods of operation without discomfort. The easy-to-reach controls ensure that everything from cutting height adjustments to speed settings can be made with just a flick of the hand.

In terms of versatility, the Cub Cadet 450 can be adapted for a wide variety of landscaping tasks. With options for attachments such as snow blowers, tillers, and other implements, this tractor can be transformed into a multi-functional tool for seasonal tasks. This capability makes it an excellent investment for homeowners looking to maximize their yard's potential year-round.

The Cub Cadet 450 also boasts an impressive warranty and follows the brand's commitment to quality and customer satisfaction. With proper maintenance, this tractor is designed to last for many years, providing reliable service season after season.

In summary, the Cub Cadet 450 is a well-rounded garden tractor that combines power, efficiency, and versatility. With its advanced engine, hydrostatic transmission, durable cutting deck, and user-friendly features, it stands out as an ideal choice for anyone looking to maintain their outdoor spaces with ease and precision.
Top Page Image Contents