Remove the filter by turning it counterclockwise using an automotive type filter wrench to loosen. See Figure 55.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FULL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MARK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OIL

 

 

 

FUEL

 

 

 

 

 

 

 

 

LOW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MARK

FILTER

 

FILTER

 

 

 

 

 

 

 

 

 

 

COOLANT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RESERVOIR

Figure 55

Reinstall the drain plug in the engine and clean up any residual oil. Refer to Figure 54.

Apply a light coating of clean oil on the gasket of the new oil filter. Thread the filter on by hand until the gasket contacts the filter base, then tighten the filter an additional 3/4 turn. Do not overtighten the filter.

Refill the crankcase to the "FULL" mark on the dipstick with the appropriate type oil.

Reinstall the oil fill cap and dipstick.

Start the engine and run for about 5 minutes. Stop the engine and check for leaks at the oil filter and drain plug.

Wait 3 minutes and re-check the oil level. If needed, add oil to bring the oil level up to the "FULL" mark.

WARNING: Never overfill the engine crankcase. The engine may overheat and/or damage may result. For best results, fill to the “FULL” mark on the dipstick as opposed to adding a given quantity of oil. Always check the level on the dipstick before adding more oil.

Dispose of used oil in an environmentally safe manner. If necessary, contact your area EPA office for proper disposal procedures and recycling center locations.

IMPORTANT: The oil fill cap and dipstick must always be installed securely in place when the engine is running. Severe engine damage could result from failure to do so.

CHECKING ENGINE COOLANT LEVEL

Before each use, the engine coolant level in the overflow reservoir should be checked to ensure it is within the operating range. Engine coolant absorbs heat from the engine and transfers the heat to the air flowing through the radiator. If the coolant level becomes low, the engine may overheat and could cause severe damage to the engine.

Use a permanent type antifreeze containing corro- sion and rust inhibitors. Dilute the antifreeze with water at a 1:1 ratio to mix the coolant solution (50% antifreeze : 50% water).

NOTE: Distilled water is recommended for the cool- ant solution IF your tap water has a high mineral content. Minerals cause scaling in the engine and the radiator coolant passages. System efficiency will be greatly reduced over time and severe engine damage may result.

Check the coolant level when the engine is cold and the tractor is on a level surface.

Raise the tractor hood and check the coolant level in the overflow reservoir on the right side of the engine. Refer to Figure 55.

If the coolant level is below the "LOW" mark, remove the cap from the reservoir and add coolant solution to the "FULL" mark.

NOTE: The cooling system is a closed type. Normally, to prevent air from entering the system, the radiator cap should not be removed.

If the overflow reservoir is empty, the radiator cap should be removed and the coolant level in the radiator checked before adding coolant to the reservoir. If necessary, first refill the system through the radiator filler neck as follows:

WARNING: It is dangerous to remove the radiator cap when the system is hot. Allow the system to cool before removing the radiator cap.

Turn the radiator cap counterclockwise to the first stop to release any pressure. Refer to Figure 50.

Push downward on the cap and turn counter- clockwise until the cap stops then lift cap off.

Slowly pour coolant into the filler neck until the level reaches the bottom of the filler neck overflow flange.

Wait a few minutes to allow as much air as possible to escape through the filler neck, then reinstall the radiator cap.

Fill the overflow reservoir to the "FULL" mark.

42

Page 42
Image 42
Cub Cadet 6284 manual Checking Engine Coolant Level

6284 specifications

The Cub Cadet 6284 is a robust utility tractor known for its versatility and reliability. Designed for both residential and commercial use, it is ideal for tasks such as landscaping, gardening, and light agricultural work. This model stands out in the compact tractor market due to its powerful engine and innovative features that boost productivity and ease of use.

At the heart of the Cub Cadet 6284 lies a powerful 28-horsepower Kohler diesel engine, which provides ample torque for demanding applications. This engine is designed for efficiency and durability, ensuring long-lasting performance and reduced operating costs. The liquid-cooled design helps to maintain optimal operating temperatures, extended engine life, and consistent power output, making it suitable for various weather conditions.

One of the key characteristics of the 6284 is its hydrostatic transmission, which offers seamless shifting without the need for clutching. This feature allows operators to maintain a steady pace while maneuvering in tight spaces or during intricate tasks. The intuitive controls enhance user experience, making it an excellent choice for both seasoned operators and newcomers alike.

The 6284 features a heavy-duty, rear-mounted three-point hitch with a standard lift capacity which enables the attachment of various implements, enhancing its versatility. With a variety of compatible attachments, including rotary cutters, plows, and loaders, users can easily switch between tasks, making it a multifunctional workhorse.

Another notable technology integrated into the Cub Cadet 6284 is the ergonomic operator station. The layout is designed with user comfort in mind, featuring an adjustable seat, easy-to-reach controls, and excellent visibility, allowing operators to work efficiently for extended periods. The compact design aids in maneuverability, especially in more confined spaces.

Additionally, the Cub Cadet 6284 is built with a sturdy frame and quality materials, designed to withstand heavy use. The all-steel construction contributes to its overall durability, ensuring that the tractor can handle tough jobs without compromising performance.

In summary, the Cub Cadet 6284 is a powerful and efficient compact utility tractor that offers reliable performance for a variety of tasks. Its combination of a robust engine, hydrostatic transmission, and ergonomic design makes it a valuable addition to any toolkit. Whether for residential gardening or more extensive commercial applications, the 6284 is equipped to tackle the job with ease and efficiency.