Cub Cadet 80 LB manual Optional Remote Deflector Part No Mounting Instructions, Description

The Optional Remote Deflector - Part No. 02004519

Mounting Instructions

1.Install the deflector tube mount (ref. 20) onto the right side of the spreader frame (from the inside) as shown.

2.Install the tube bracket mount (ref. 19) to the right side of the frame using appropriate hardware as shown.

a.Install 1/4-20 x 2 (ref. 5) through frame plate using spacer (ref. 3), washer (ref. 6), and tighten using 1/4-20 nut (ref. 10).

b.Install nylon washer (ref. 2), bracket mount (ref. 19) nylon washer (ref. 2) and tighten nut (ref. 8) until bracket mount (ref. 19) easily turns.

3.Install offset bracket (ref. 4) onto deflector (ref.16)

a.Slide Long end of offset bracket into slot on deflector (ref. 16)

b.Install 1/4-20 screw (ref. 9) and tighten sub assembly using 1/4-20 nut (ref. 8)

Drill 9/32" Hole

Ref.
No.	Part No.	Description	Qty.
1	00010171	Retainer “C” Clip	1
2	00018628	Nylon Washer, 1/4	6
3	00030503	Deflector Arm Mount Spacer	1
4	00035030	Offset Bracket Deflector	1
5	00060029	Machine Screw, 1/4-20x2	1
6	00060033	Flat Washer, 1/4”	1
7	00060034	Operating Lever and Rubber	1
8	00060036	Lock Nut, Nylon Insert, 1/4	8
9	00060057	Machine Screw Pan Head, 1/4-20x7/8	5
10	00060059	Hex Nut, 1/4-20	2
11	00060071	Hex Lock Nut, 5/16-18	1
12	00060072	Nut, Nylon Insert, 5/16-18	1
13	00060073	Lock Washer, 5/16	1
14	00061052	Cotter Pin, 1/8 x 1	1
15	00061053	Flat Washer, 3/8	1
16	00061066	Deflector Tube, Plastic Only	1
17	01006251	Deflector Actuator Rod	1
18	01006252	Lever Rod Deflector Bracket	1
19	01006253	Tube Bracket Mount, Lever, Deflector	1
20	01006254	Deflector Tube Mount	1
21	00030418	Remote Bracket	1
22	00031168	HHCS, 1/4-20 x .75, SS	3
23	00060047	Machine Screw, 1/4-20 x 1.50, SS	1

9.5

Right Handle

4.	Slide deflector subassembly onto deflector tube mount
	(ref. 20)
a. Install washer (ref. 15) onto deflector tube mount
	and lock in place using cotter pin (ref. 14)
5.	Fasten offset bracket (ref. 4) to bracket mount (ref. 19)
	using appropriate hardware.
a.	Install 1/4-20 screw (ref. 9) and tighten sub

NOTE: Adjust the friction at the three deflector arm pivot points by tightening the nuts and then backing them off 1/8th turn. Ad- just the friction at the operating lever pivot so that it will hold its position.

23	21	8
8		1
2		7

22

	assembly using 1/4-20 nut (ref. 8) until deflector (ref.
	16) moves easily on deflector tube mount (ref. 20)
6.	Install lever rod bracket (ref. 18) to bracket mount (ref.
	19).
a. Install, making sure small flange of lever rod bracket
	faces to the inside of the spreader, using
	appropriate hardware.
7.	Install remote bracket (ref. 21) onto right side of upper
	handle.
a. Install using one 1/4-20 (ref. 23) and one 1/4-20 nut
	(ref. 8)
8.	Install operating lever (ref. 7) using appropriate
	hardware
9.	Install rod (ref. 17) into operating lever (ref. 7) and into
	lever rod bracket (ref. 18)
10.	Slide deflector up toward the bottom of the hopper as
	far as it will go.
11.	Place the operating lever (ref. 7) in the “OFF” position
	and adjust the lock nut (ref. 11) so it is down against
	the lever rod bracket (ref. 18).
a.	Tighten nylock nut (ref. 12) up against the underside
	of the lever rod bracket (ref. 18)

9 or	22		20	17
			8
			14	12
			10
		10	9
		6		11
5		3	2	13
				18
		9		8
	2		19	2
				8
		8		9
		4

16 15

5