CS202
2-Cycle Trimmer
Operator’s Manual
Removing Unit From Carton | Assemble The Unit | |
|
|
|
Slot
|
|
| Bracket | |
1 |
|
| 2 |
|
Remove all contents from | Slide shield’s slot onto | |||
carton. | mounting bracket. Rotate | |||
|
|
| shield onto shaft. Push | |
|
|
| square bolt through shield | |
|
|
| and bracket. Tighten | |
|
|
| washer and wing nut | |
|
|
| onto bolt. | |
Assemble The Unit |
|
|
|
|
|
|
|
| |
|
|
|
|
|
| Min. 6” | |
Knob | 4 | |
3 | ||
Remove the protective cap | Loosen the bolt. Move the | |
and gray spacer from the | handle to the location that | |
upper and lower shafts. | provides the best grip. Move | |
Push the attachment into | the handle a minimum of 6 | |
the coupler. Turn the knob | inches away from the shaft | |
clockwise to tighten. | grip. Tighten the bolt until the | |
| handle is secure. | |
Starting The Unit |
| |
Primer | Choke Lever | |
Bulb | ||
|
• 3/8” Socket
Starter Rope | Fuel Cap |
|
| Page 1 | |
|
| |
On/ Off Switch |
| — |
|
| |
| English | |
|
| |
| Throttle Control |
|
|
|
| 40:1 |
| 10 X |
| |
5 | 6 | 8 | ||
7 | ||||
Mix thoroughly in a separate | Place unit on a level surface. | Press primer bulb 10 times, | Move choke lever to | |
fuel can: | Fill fuel tank. | or until fuel is visible | Position 1. |
–3.2 fl. oz. of
–1 gallon of unleaded gasoline
NOTE: Do not mix directly in the unit fuel tank.
Starting The Unit
|
|
| Choke Lever |
|
| 5 X |
|
19 | 10 | 11 | 12 |
Crouch in starting position. | SQUEEZE and HOLD | Pull rope 5 times. | Move choke lever to |
| throttle for ALL further |
| Position 2 and squeeze |
| steps. |
| throttle. |
Reloading The Line*
|
| Need Help? |
|
| Call |
| |
Cutting Head Shield | DIDN’T START? |
| |
|
| ||
| Repeat the starting instructions. |
| |
| If the unit still fails to start, |
| |
| refer to the operator’s manual |
| |
| for additional starting and |
| |
| troubleshooting information. |
| |
|
|
| Page 6 |
| Choke Lever |
| — |
13 | 14 | 15 | Français |
|
|
| |
Pull rope | Continue to squeeze | Continue to squeeze |
|
engine. Run unit for | throttle. Move choke lever | throttle. Run unit for an |
|
seconds to warm up. | to Position 3. | additional 60 seconds to |
|
|
| complete |
|
|
| may be used during this |
|
|
| time. |
|
Bump | Outer |
|
|
|
Spool |
|
|
| |
Knob |
|
|
| |
|
|
|
| |
|
| Inner |
| Top Hole |
| Spring |
| Bottom Hole | |
1 | Reel | 3 | ||
2 |
| 4 | ||
Unscrew the bump knob | Remove the inner reel and | Cut one | Insert the end of one line | |
counterclockwise. | spring. |
| length of new 0.095” split | into the top hole and the |
|
|
| line trimming line. Split each | end of the other line into the |
|
|
| end about 6 inches (150 | bottom hole. |
|
|
| mm). |
|
Reloading The Line | For replacement line, call |
| |
| an authorized service dealer. |
For single line installation or replacement spool installation instructions, refer to the Replacing the Trimming Line section of this manual.
*This is to assist in the reloading of Splitline® only. These instructions are NOT part of the fast assembly instructions. Line does not need to be installed on the initial assembly and
18
Hold the inner reel and outer spool together. Firmly pull the two line ends to release them from the holding slots. Screw the bump knob on clockwise. Tighten the bump knob securely.
Split Wall
5
Wind the line tightly in the direction shown on the inner reel. The split wall will divide the line. Wind the line until it is completely divided and about 6 inches (150 mm) of line remains.
Holding Slots
6
Insert the two
Eyelets
7
Pass the two line ends through the eyelets. Place the spring inside the inner reel. Insert the inner reel into the outer spool. Push the inner reel and outer spool together.
Español — Page 11
IMPORTANT: READ THE OPERATOR’S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT.
NEED HELP? CALL 1-877-282-8684 IN U.S. OR 1-800-668-1238 IN CANADA
| 03/12 |