•Place a block of wood between the center deck housing baffle and the cutting blade to act as a stabilizer. See Figure 16.

Hex Flange Nut

Wood Block

Spindle Assembly

Figure 16

•Use a 1-1/8" wrench to remove the hex flange nut that secures the blade to the spindle assembly. See Figure 16.

To properly sharpen the cutting blades, remove equal amounts of metal from both ends of the blades along the cutting edges, parallel to the trailing edge, at a 25° to 30° angle.

IMPORTANT: If the cutting edge of the blade has already been sharpened, or if any metal separation is present, replace the blades with new ones.

It is important that each cutting blade edge be ground equally to maintain proper blade balance. A poorly balanced blade will cause excessive vibration and may cause damage to the tractor and result in personal injury.

The blade can be tested by balancing it on a round shaft screwdriver. Grind metal from the heavy side until it balances evenly.

IMPORTANT:When replacing the blade, be sure to install the blade with the side of the blade marked ‘‘Bottom’’ (or with a part number stamped in it) facing the ground when the mower is in the operating position.

IMPORTANT:Use a torque wrench to tighten the blade spindle hex flange nut to between 70 lbs-ft and 90 lbs-ft.

Battery

The battery is sealed and is maintenance-free. Acid levels cannot be checked and fluid can not be added.

•Always keep the battery cables and terminals clean and free of corrosive build-up.

•After cleaning the battery and terminals, apply a light coat of petroleum jelly or grease to both terminals

•Always keep the rubber boot positioned over the positive terminal to prevent shorting.

IMPORTANT: If removing the battery for any reason, disconnect the NEGATIVE (Black) wire from it’s terminal first, followed by the POSITIVE (Red) wire. When re-installing the battery, always connect the POSITIVE (Red) wire its terminal first, followed by the NEGATIVE (Black) wire. Be certain that the wires are connected to the correct terminals; reversing them could change the polarity and cause damage to your engine’s alternating system.

Jump Starting

WARNING: Never jump start a damaged or frozen battery. Be certain the vehicles do not touch, and ignitions are off. Do not allow cable clamps to touch.

•Connect positive (+) cable to positive post (+) of your tractor’s discharged battery.

•Connect the other end of the cable to the (positive +) post of the jumper battery.

•Connect the second cable (negative –) to the other post of the jumper battery.

•Make the final connection on the engine block of the stalled tractor, away from the battery. Attach to a unpainted part to assure a good connection.

IMPORTANT: If the jumper battery is installed on a vehicle (i.e. car, truck), do NOT start the vehicle’s engine when jump starting your tractor.

•Refer to the instructions on page 13 to start the tractor .

•Set the tractor’s p[arking brake before removing the jumper cables, in reverse order of connection.

•Allow the tractor’s engine to run for 15 minutes before shutting it off to allow the alternating system time to charge the discharged battery.

Charging

If the unit has not been put into use for an extended period of time, charge the battery with an automotive- type 12-volt charger for a minimum of one hour at six amps.

WARNING: Batteries give off an explosive gas while charging. Charge battery in a well ventilated area and keep away from an open flame or pilot light as on a water heater, space heater, furnace, clothes dryer or other gas appliances.

20

Page 19 Page 21
Page 20
Image 20
Cub Cadet LT1018, LT1022 manual Battery, Jump Starting
Page 19 Page 21

LT1018, LT1022 specifications

The Cub Cadet LT1022 and LT1018 are two standout models in the world of riding lawn mowers, designed for homeowners who want efficiency, comfort, and the power to tackle their mowing tasks with ease. Both models exemplify the fusion of innovative technologies and user-friendly features, making them an ideal choice for maintaining lawns of various sizes.

Starting with the Cub Cadet LT1022, this riding mower is equipped with a powerful 22 HP Kohler engine, ensuring ample power to handle tough mowing conditions. The 42-inch cutting deck provides a wide mowing path, reducing the number of passes needed to cover larger lawns, which ultimately saves time. The LT1022 also features a sophisticated hydrostatic transmission that allows for smooth and effortless speed adjustments, giving the operator complete control over mowing speed without the need to shift gears.

Another notable feature of the LT1022 is its enhanced cutting technology. The mower is designed with a mulching kit, side discharge, and bagging options, providing versatility in how grass clippings are managed. The adjustable cutting height, ranging from 1.5 to 4 inches, ensures precise grass cutting tailored to the user’s lawn care preferences.

On the other hand, the Cub Cadet LT1018 caters to those who may require a slightly smaller package without sacrificing performance. With an 18 HP Kohler engine, it still packs enough power for medium-sized lawns. The 42-inch cutting deck allows for efficient mowing, similar to the LT1022, making it suitable for navigating tight spaces while effectively managing larger areas as well.

Both models feature a comfortable high-back seat, ensuring that users can mow for extended periods without discomfort. The easy-to-use dashboard provides clear visibility of important information, including fuel level and blade engagement status, enhancing the overall user experience.

In terms of ease of maintenance, the LT1022 and LT1018 come with accessible service points, making it simple for owners to perform routine checks and maintenance tasks. The durable construction of both mowers ensures that they can withstand the rigors of regular use, providing a reliable mowing solution for years to come.

In summary, the Cub Cadet LT1022 and LT1018 offer a blend of power, advanced cutting technologies, and user-friendly features that make them excellent choices for any homeowner looking to maintain their lawn efficiently and effectively.
Top Page Image Contents