LEVELING THE MOWER DECK

When leveled correctly the mower deck should be level side to side, and should be approximately a 1/8 to 1/4 inch lower in the front of the deck.

Side to Side Leveling

If the cutting deck appears to be mowing unevenly, a side to side adjustment can be performed. Adjust if necessary as follows:

•With the tractor parked on a firm, level surface, place the deck lift handle in the top notch (highest position) and rotate both outer blades so that they are perpendicular to the tractor frame.

•Measure the distance from the outside left blade tip to the ground and the distance from the outside right blade tip to the ground. The measurements should be equal. If they’re not, proceed to the next step.

•Comparing the two measurements, determine whether the left side of the deck must be raised or lowered.

•Loosen, but do not remove, the hex cap screw on the left deck hanger bracket. Refer to Figure 30.

•Level the deck by using a wrench to turn the adjustment gear (found immediately behind the hex cap screw just loosened) clockwise to raise the left side of the deck, or counterclockwise to lower the left side of the deck. See Figure 30.

Lower

LT.

 

Raise LT.

Side of Deck

 

Side of Deck

Adjustment

 

Hex Cap

 

Screw

 

 

 

 

 

Gear

 

 

 

Figure 30

•The deck is properly leveled when both blade tip measurements taken earlier are equal.

•Retighten the hex cap screw on the left deck hanger bracket when proper adjustment is achieved.

Front to Back Leveling.

The front of the deck should be approximately 1/8 to 1/4 inch lower than the rear of the deck. Adjust if nec- essary as follows:

•With the deck raised off of the ground, rotate the outer blades so that they are parallel to the frame of the tractor.

•If the side to side leveling was done correctly, measuring just the right blade should be acceptable to attain the correct back to front pitch of the deck.

•Measure the distance from the front tip of the blade to the ground and the distance from the rear tip to the ground. The front distance should be 1/8 to 1/4 inch less than the rear. If it is not, proceed to the next step.

•From the front of the tractor, loosen the outer nuts on the deck front hanger rod, and turn them away from the inner nuts. See Figure 31.

Hex Nuts

Front Hanger

Rod Bracket

Front

Hanger

Rod

Figure 31

•If the front of the deck was too low, turn the inner hex nuts clockwise against the hanger bracket to shorten the front hanger rod and raise the front of the deck. See Figure 31.

•If the front of the deck was too high, turn the hex nuts counterclockwise to lengthen the front hanger rod and lower the front of the deck.

IMPORTANT: The deck front hanger rod should be at the front of the slots of the front deck bracket. If one side of the rod is not at the front of its slot, turn the inner hex nut on that side until rod just touches the front of the slot. Then re- measure and re-adjust the front hanger rod as necessary.

•When the correct pitch of the deck is acquired, secure the inner hex nuts with a wrench and tighten the outer hex nuts against the inner hex nuts to lock them in the adjusted position.

28

Page 27 Page 29
Page 28
Image 28
Cub Cadet RZT 50 manual Leveling the Mower Deck, Side to Side Leveling, Front to Back Leveling
Page 27 Page 29

RZT 50 specifications

The Cub Cadet RZT 50 stands out in the world of residential zero-turn mowers, offering a compelling combination of power, performance, and convenience. Designed for homeowners who prioritize both efficiency and lawn care aesthetics, the RZT 50 is an excellent choice for tackling various mowing challenges.

At the heart of the RZT 50 is a robust 24-horsepower Kohler engine. This powerful engine provides ample torque and speed, enabling users to tackle extensive lawns with ease. The mower features a 50-inch cutting deck, which can handle larger areas while maintaining a precise cut. Its unique dual-blade design ensures optimal grass clipping and minimizes the number of passes needed to achieve a well-manicured lawn.

One of the standout features of the RZT 50 is its innovative zero-turn technology. This system allows for exceptional maneuverability, enabling the mower to turn on a dime. This agility proves invaluable when navigating around trees, flower beds, and other landscaping elements, reducing the time and effort required for yard maintenance.

The RZT 50 is equipped with a Cub Cadet Endurance Series engine that enhances durability and reliability. Coupled with a rolled steel frame, this mower is built to withstand the rigors of regular use. The mower’s wide rear tires provide superior traction, allowing it to maintain stability on various terrains, from flat lawns to inclines.

Comfort is not overlooked in the RZT 50’s design. It features a high-back seat and adjustable armrests, enabling the operator to work longer without fatigue. Additionally, the soft-touch controls and easy-to-use dashboard ensure an intuitive mowing experience, even for those new to zero-turn mowers.

Maintenance is simplified with features like the easy-to-access deck washout port, which makes cleaning the mower deck a breeze. Regular upkeep is vital for keeping the mower in top condition, and Cub Cadet has made this process more user-friendly.

All these features come together to make the Cub Cadet RZT 50 a remarkable choice for homeowners. Whether you’re looking to maintain a small yard or manage a larger expanse, this mower combines power, precision, and comfort to deliver excellent results, making lawn care a task that can be completed efficiently and effortlessly.
Top Page Image Contents