Cub Cadet S7237 Zero Turn Break-In And Operating Proce- dures, Orientation, Initial Operation

of the deck on each side of the mower. (Four dimensions.)

Note: The front edge of the mowing deck should be 1/8"-1/4" below the rear edge of the deck so that the blades are cutting grass in only the front half of their circular path. This decreases friction and reduces the drive power required.

c.If the cut height is below 1-1/2” the pitch should not exceed 1/16”. If the dimension at the front of the mowing deck is 1/8"-1/4" lower than the dimension at the rear of the deck on each side of the mower, do not adjust. If not, you will need to adjust the Deck Lift Link (See Figure 8). You may also need to adjust the Deck Links (See Figure 8).

Deck Lift Link

Figure. 8 Deck Links

Note: The pitch should not exceed 1/16” if the cut height is below 1-1/2”.

d.Lower the mower deck to the cutting position. With a wrench loosen the inner rear nut on the Deck Lift Link. To adjust the deck up or down, use a wrench and with a few turns, adjust clock- wise or counter clockwise the outer rear nut of the Deck Lift Link. Repeat this procedure on the opposite side of the Mower. Once the deck is adjusted, retighten bolts.

e.With the deck still in the cutting position, adjust the Deck Links. With a wrench loosen the top inner bolt of the Deck Link. To adjust the side of the deck up or down turn the top bolt clockwise or counter clockwise a few turns. Adjust both front and rear Deck links as necessary. Retighten nuts.

f.Raise the mowing deck to the transport position using the upper foot pedal.

g.Use the second foot pedal to lower the mowing deck to the cutting position and repeat step “b.” above to make sure that the desired cutting height has been attained. If the dimensions are not cor- rect, repeat steps “c.” through “f.” above.

5.Lubricate all fittings listed in the maintenance sec- tion.

D.Zero Turn Break-In And Operating Proce- dures

DANGER:

Reread the “When Mowing” Safety Precautions.

The following procedures are suggested for operators of ride-on machines which have zero turn capabilities.

1.Orientation:

a.Read the entire Operator’s Manual.

b.Sit on the machine, adjust the seat position front to rear, then adjust the seat back recline, then adjust the arm rests. Swing the Steering column inward and lock with the adjustable ratchet han- dle. Finally, adjust the Steering wheel tilt with the adjustable ratchet handle.

c.Become familiar with all of the machine controls, instrumentation, safety and instruction signs, and safety devices.

d.Move (or have moved) the machine to a safe, level area with no obstructions including objects, pedestrians, and animals.

2.Initial Operation:

a.Use protective equipment for eyes, hands, hear- ing, feet, legs, head and other areas of the body if needed — safety eye glasses, gloves, earplugs, boots, hats, etc.

WARNING:

Hearing Protection is required for all operator expo- sure exceeding two (2) hours.

b.Ensure that the area is free of animals and bystanders, especially children!

c.Survey the area where the equipment is to be used to make sure it is free of debris, sticks, stones, wires, bones, and other foreign objects which could cause injury to bystanders, damage to the machine, or damage to nearby facilities.

d.Inspect the machine to make sure:

1.All guards, shields (including mower chute deflector) are in their proper place, are secure, and are functional.

2.That there are no spilled or leaking fuel or oil sources, nor loose fuel or hydraulic tank caps, hoses or fittings.

3.That there are no loose or missing hardware nor any missing items.

4.That no non-approved devices are installed.

5.That all safety signs and decals are properly installed and legible.

e.This is a one person machine, operator only! Rid- ers are not permitted under any circumstance!

f.To start the engine on the machine:

1.Make sure the park brake is set to the “ON” position, the speed control pedals are in the neutral position, and the Power Take Off (PTO

13