UNPACKING & PLACEMENT | 2. Remove the filter timer from the lid by flipping | ||
1. Remove your Cuisinart® | ® | the lid over and pressing on the plastic tab. | |
3. Wash both tanks and plastic lid in mild, soapy | |||
Countertop Filtration System carefully from | |||
the box. |
| water, and rinse. Replace the filter timer. | |
2. Position the unit on a stable flat surface, close | 4. Lift the filter from the bowl and allow water to | ||
to a main power outlet. Avoid direct sunlight | drain. | ||
and keep out of the reach of children. | NOTE: The filter's loose | ||
|
| ||
3. Allow at least 3 inches of space around | carbon dust may slightly | ||
the sides and rear of the unit for proper air | darken water while soaking. | ||
circulation. |
| 5. With the Cuisinart® logo | |
4. Remove filter from upper tank and carefully | |||
facing up, insert the water | |||
follow the SETUP instructions below. You will | filter into the upper water | ||
need a large bowl, a pitcher (or another type | tank and push firmly into | ||
of container) and a glass. |
| place. | |
NOTE: Do not plug in unit until ALL steps of | 6. Place the upper tank on a | ||
SETUP are complete. |
| pitcher (or another type of | |
Water Filter SetUp |
| container) and fill with cold | |
| tap water. Allow to drain for | ||
NOTE: For optimum filtering and flow rates, | 5 minutes to flush out any | ||
the water filter must be prepared and installed | |||
remaining carbon dust, then | |||
exactly as follows: |
| ||
| pour out remaining water. | ||
|
| ||
Preparing the Water Filter |
| Water Dispenser SetUp | |
1. Remove the filter from its packaging. | |||
NOTE: Use only cold tap water to fill the unit. | |||
NOTE: The filter may contain a small amount | |||
Filling the Upper and Lower Tanks | |||
of loose carbon dust. It may also appear moist, | |||
have a faint smell of plastic or a slight yellowish | 1. Place the upper tank onto the lower tank and | ||
tint – these are all normal. DO NOT wash filter | |||
cover with the lid. | |||
with soap or water. |
| ||
| Lid | ||
2. Place water filter in |
| ||
| Upper | ||
empty bowl sideways |
| ||
(see image). Pressing it |
| water tank | |
|
| ||
firmly to the bottom of the |
|
| |
bowl, and being careful |
| Lower | |
not to pour water directly |
| water tank | |
onto the filter. Slowly add |
|
| |
enough cold water to fully submerge and |
| ||
cover the filter by at least 1 inch. (You |
| ||
should see bubbles escaping the filter.) | 2. Place assembled tanks on base. NOTE: The | ||
3. Continue to hold filter under water for at least | |||
vertical groove on the upper tank must face | |||
30 seconds. |
| the back of the unit. | |
4. Release the filter and let it |
| 3. Carefully lift the flip top lid and add cold | |
soak at least 15 minutes. |
| ||
| water to the FILL line. NOTE: This is a gravity | ||
NOTE: While soaking, the |
| ||
| fill system. To increase the filtering flow rate, | ||
filter should be partially |
| ||
| continue adding water to the FILL line of the | ||
submerged and may tilt to one side. | |||
upper tank until tanks are completely full. | |||
|
| ||
Installing the Prepared Water Filter |
| 4. During the initial setup, allow | |
1. While the filter is soaking, remove the lid, | |||
for water to filter into and completely fill upper | |||
upper water tank and lower water tank. | and lower tanks. |