Battery Installation, Service life of batteries

BASIC CONNECTION

F: Connecting to an external decoder or a power amplifier

When DVD discs recorded in Dolby digital, MPEG audio or other formats are played, corresponding bit stream is output from the player,s COAXIAL digital audio output connector. When the player is

connected to an external decoder or a power amplifier, you can enjoy quality of theatre level at your home!

REMOTE CONTROL PREPARATION

Battery Installation

Insert the batteries while observing the positive (+) and Negative (-) polarities as Figure A.

Service life of batteries

CD	Sound	Digital output setting
	recording format	Digital output setting


		PCM(44.1KHZ sampling)*1
	Dolby digital	Raw
		OFF
DVD	DTS	Raw
DVD	DTS	OFF
		OFF
	Linear PCM	PCM(44.1KHZ sampling)
	Other	PCM(44.1KHZ sampling)
	Linear PCM	PCM(44.1KHZ sampling)
MP3	MP3	PCM(44.1KHZ sampling)

*1 sound having 192KHz sampling is converted to 48KHz sampling when it is output from the Coaxial digital audio output connector.

Note: Please refer to the setup operations for setup method.

For your reference:

Dolby Digital (AC-3),a digital sound compression technique developed by the Dolby Laboratories Licensing Corporation supports 5.1-channel surround output and stereo sound system enables the capacity of mass storage recorded in discs Linear PCM is a signal-recording format used in CD s While CD s are recorded in 44.1KHz/16bit, DVDs are 48KHz/16bit up to 192KHz/24bit.

Caution for the coaxial audio output connector.

Do not connect an amplifier (with an Coaxial digital input connector) which does not contain the Dolby Digital (AC-3) or MPEG audio decoder, otherwise it maybe harmful to your ears and damage your speakers, Choose RAW in the digital audio setup

to activate coaxial or optical output when playing disc with DTS output.

TV set(optional)

Euro SCART

Video/audio (optional) (optional)

S-Video cord (optional)

DVD/CD player

5.1 CH

(optional)

Coaxial audio cord

Decoder of amplifier with Dolby digital (AC-3) or MPEG (optional)

The batteries normally last for a year although this depends on the operation and on how often the remote control is used.

If the remote control unit fails to work even when it is operated near the player, replace the batteries with new ones. Use size AAA UM-4 batteries (2 pieces).

Notes:

Do not use rechargeable (Ni-Cd) batteries.

Install batteries correctly observing the (+/-) polarity signs.

Do not drop, step on the remote control, otherwise it may damage the parts or lead to malfunctioning.

Use only the recommended battery type or equivalent (voltage and size).

Always replace a complete set of batteries at the same time.

Do not mix batteries of different types.

Never mix new and used batteries in the same compartment.

Remove exhausted batteries immediately.

Remove batteries when product is not in use.

Do not dispose of batteries in fire as they may explode.

Do not recharge non-rechargeable batteries.

Do not short circuit the supply terminals.

Ensure batteries are stored away from metal objects as contact may cause a short circuit.

Remote control operation range is no more than 5 m from and within about 60 degree wide in front of the unit (Figure B).

Notes:

Do not point bright lights to the remote control sensor. Do not place objects between the remote control and the remote control sensor.

Do not use this remote control together with the remote control of any other equipment.

Remark:

Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

Remoto control sensor

DVD/CD/MP3/MPEG4 PLAYER

DVD3602UKT

Among 5 meters

30		30
OPEN/CLOSE			POWER
OSD	P/N	REPEAT	A-B
SHUFFLE			ANGLE
1	2 3
4	5 6
7	8 9
TIME	0 10+
	MUTE	SLOW	PROG
VOL	STEP	L/R	16:9/4:3
SETUP			AUDIO
	ENTER
RESET			RETURN
TITLE
PBC	PAUSE	PLAY	STOP
REV		PREV	NEXT