v2.00.47 |
| None |
| |
|
|
|
|
|
|
|
|
|
|
v1.00.36 |
|
|
| |
|
| First release |
| |
|
|
|
| |
v1.00.37 |
|
|
|
|
|
|
|
| |
Problem Fixed:
| Firmware Version |
|
| Problems Fixed | |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| 1 | The “Time Zone Offset” cannot be changed via Web GUI but there is no |
|
|
|
|
| problem for CLI command. (DRU20100318000003) |
| v3.60.28 |
|
| 2 | User cannot add a VLAN name with space in CLI but no problem for Web |
|
|
|
| ||
|
|
|
|
| GUI (DI20100209000008) |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| 1 | The “Port ID” and “Port ID Subtype” in the LLDP TLV information display |
|
|
|
|
| Hex string in Web UI instead of displaying alphanumeric one. |
| v3.50.23 |
|
|
| (DI20090330000015) |
|
|
|
|
| |
|
|
|
| 2 | The stack cannot be established due to that the switch’s MAC overlapped. |
|
|
|
|
| (DI20091208000009) |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| 1 | If user changes switch’s unit ID to 2 and queries the ifTable MIB file, |
|
|
|
|
| system will hang up. |
|
|
|
| 2 | When user tries to disable Telnet via the Web UI while running the |
|
|
|
|
| command “show configuration running”, the Telnet session will not be |
|
|
|
|
| disabled and there is no warning message, either. |
| v3.00.43 |
|
| 3 | When user tries to configure 128.0.0.0 subnet mask in Trusted Host |
|
|
|
| ||
|
|
|
|
| feature, the CLI will accept the command but Web UI will display |
|
|
|
|
| “128.0.0.0 is not a valid IP mask” warning message. |
|
|
|
| 4 | In Port Security, when user changes the setting of “lock_address_mode”, |
|
|
|
|
| the value of “admin_stat” will be changed, too. |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| 1 | When executing the command ‘configure ipif’ and key in the ‘?’ to query |
|
|
|
|
| the next available parameter, it will display ‘system’ instead of ‘System’. |
|
|
|
| 2 | Users can only open two web sessions in stacking architecture. |
|
|
|
| 3 | Users can configure the stacking port as the LACP port. |
| v2.50.43 |
|
| 4 | When configuring Trust Host, Syslog, SNMP, SNTP, Radius and ARP |
|
|
|
|
| features; Illegal IP address is acceptable without any error or warning |
|
|
|
|
| message. |
|
|
|
| 5 | When user configures port security with trap enabled on specific ports via |
|
|
|
|
| CLI and afterwards configures port security on other ports with no trap |
|
|
|
|
| enabled via Web UI, using the ‘show port_security’ or ‘show configuration |
|
|
|
|
| running’ commands on CLI, the user can see that the trap appears also |
11
