Planning the Installation

Cabinet Layout

•Any openings in the wall behind the appliance or in the floor underneath it must be sealed.

 

 

 

 

 

 

WARNING

•

Both the gas supply piping and shut-off valve and the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

electrical outlet must be located so they do not interfere

 

Failure to meet or exceed the minimum dimensions

 

 

 

with the range when it is installed.

 

stated below may result in a fire hazard.

 

 

•

All dimensions shown are based on standard American

•

Carefully check the location where the range is to be

 

cabinets 36 inches (914mm) high at the finished

 

installed. For best performance, the range should be

 

 

 

countertop by 24 inches (610mm) deep, with a 25

 

placed away from drafts that may be caused by doors,

 

 

 

inch (635mm) overall countertop depth. All minimum

 

windows and heating and air conditioning outlets.

 

 

 

clearances shown MUST be maintained.

•

To reduce the risk of personal injury and to reduce

 

•

If cabinet storage space is to be provided directly above

 

accumulated smoke in the room, Dacor strongly

 

 

the range, the risk of personal injury may be reduced by

 

recommends installing a range hood. A range hood

 

 

 

installing a ventilating hood that projects horizontally a

 

should project horizontally a minimum of five (5) inches

 

 

 

minimum of 5 inches beyond the face of the cabinets.

 

beyond the face of the cabinets.

 

 

•

The installation must allow for the following:

•

The range may be installed flush to the rear wall.

 

 

 

 

 

 

 

Dacor highly recommends installing a non-combustible

 

◊ Access to the gas shut-off valve when the unit is

 

material on the rear wall above the range and up to the

 

 

installed.

 

 

 

vent hood. It is not necessary to install non-combustible

 

◊

Access to the electrical outlet, when the range is in

 

materials behind the range below the countertop height.

 

 

 

 

place.

 

 

•

Regardless of the type of back wall surface, the range

 

 

 

 

 

◊

The gas supply piping, gas shut-off valve and the

 

must not be installed or operated without the backguard

 

 

 

 

electrical junction box or receptacle must be located

 

in place.

 

 

 

 

 

 

 

 

 

 

 

 

 

so they do not interfere with the range when it is

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

installed.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

◊ The electrical outlet and gas shut off valve must

 

 

 

 

 

 

 

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

be located so that the range can be pulled out for

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

service while the appliance remains connected.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

36” (914mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30 1/16”

Recommended

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(764mm)

30” (762mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Minimum

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Non-Combustible surface along back wall recommended

30” (762mm)

min.*A

**

 

 

Suggested

 

 

 

 

location of

 

 

 

 

 

 

utilities***

*Vertical to combustible surface

**Cabinet depth is at discretion of customer but cabinet face MUST NOT protrude further than rear of front panel, see product dimesions

***Consult local code for exact location

requirements.

Cutout Dimensions

5