Dacor ER48D, ER36D-C, ER48D-C Gas and Electrical Service, The installation must allow for the following:, Standard Cutout with, Range Hood, Cutout with Optional ERV Raised Vent (Top View)

Planning the Installation

Cabinet Layout

•Carefully check the location where the range is to be installed. For best performance, the range should be placed away from drafts that may be caused by doors, windows and heating and air conditioning outlets.

•To reduce the risk of personal injury and to reduce accumulated smoke in the room, Dacor strongly recommends installing a range hood. A range hood should project horizontally a minimum of 5 inches beyond the face of the cabinets.

•All maximum and minimum dimensions and clearances shown in the diagrams below must be maintained for safe operation.

•The range may be installed flush to the rear wall.

Dacor strongly recommends installing a non-combustible material on the rear wall above the range and up to the vent hood or installation of a backguard. It is not necessary to install non-combustible materials behind the range below the countertop height.

•Any openings in the wall behind the appliance or in the floor underneath it must be sealed.

CUT-OUT DIMENSIONS

Range Model	F	G	H
ER36D	42” (1067mm)*	36 1/16”	33 ½”
	36” (914mm)**	(916mm)**	(848mm)
ER48D	54” (1372mm)*	48 1/16”	43 ½”
	48” (1219mm)**	(1221mm)**	(1102mm)
	* Recommended	**Minimum

Gas and Electrical Service

•The shaded area shown denotes the location of the gas inlet and the electrical junction box/receptacle. This is the recommended location. For replacement purposes, the location of the existing utilities may be utilized provided they do not interfere with the sides or rear of the range. Check local building codes for permissible gas valve locations.

•An external manual shut-off valve must be installed between the gas inlet and the range, for the purpose of turning on or shutting off gas to the appliance.

The installation must allow for the following:

•Access to the gas shut-off valve when the unit is installed.

•Access to the remote circuit breaker panel/fuse box, when the range is in place.

•The gas supply piping and shut-off valve, and the electrical junction box/receptacle must be located so they do not interfere with the range when it is installed.

•The junction box and gas shut off valve must be located so that the range can be pulled out for service while the appliance remains connected.

	Backsplash
Minumum Countertop Height:
30 1/4” (768 mm)
Maximum Countertop Height:
			2 13/16"
36 1/2” (927 mm)
	3/8" (10 mm)		(71.4 mm)
non-combustible	Min. flat countertop
	overhang
rear wall recommended
		H

Standard Cutout with

Range Hood

F

10" (254 mm) Min.

to combustible side

3

walls above the range

(both sides)

13” (330mm)

Max.5

G

Cutout with Optional ERV Raised Vent (Top View)

Non-combustible

surface along

back wall

recommended

30”

(762mm)

G

Min.1

2, 5

APPROVED RAISED VENT MODEL NUMBERS

Range Model

ERV Raised Vent Model

3

Suggested

ER36D

ERV36-ER

location of

36 1/2”

utilities4

ER48D

ERV48-ER

(927mm)

Max.

1 Vertical to combustibles directly above cooking surface;

IMPORTANT: See the raised vent installation instructions

if installing an overhead vent hood, also check the hood

specifications for minimum required clearances.

for the duct and electrical installation requirements. Use

2 Measured from range top panel.

only the raised vent models specified below.

3 Cabinet/countertop depth is at discretion of customer but

cabinet face MUST NOT protrude further than rear of front

panel, see product dimensions.

All tolerances: +1/16”, -0 (+1.6mm, -0)

4 Consult local code for exact location requirements.

5 Not applicable for cabinets more than a horizontal

Unless otherwise stated

distance of 10” (254mm) from the edge of the range.