Planning the Installation

Location Planning - Enclosed Cabinets

•Maintain all minimum clearances specified on pages 7 and 8.

•For proper outdoor grill operation, provide a flat, level mounting surface with minimum 3/4” thickness.

•All models are designed to allow installation in combustible or non-combustible base material structures.

•On installations without a LP cylinder tank located below the unit, plan the installation so that the gas shut-off valve and pressure regulator are accessible after the appliance is installed so that gas and power can be turned off if service is required. Also, make sure the electric plug can be disconnected easily during service.

Optional Finish Trim Kits

The optional finish trim can be installed on the countertop to finish the sides and back of the countertop opening. The stainless steel finish trim can be caulked to the countertop and should be secured to the base enclosure with flat head screws. Center the trim within the cutout dimensions noted in this manual, then utilizing the deck screws along with the holes located along the vertical sides of the finish trim, install them securely to the base enclosure countertop sub- straight. Install the trim before installing the grill.

Enclosed Cabinet Installations with a LP Cylinder

•When using a LP-gas cylinder, it must be completely enclosed, It must also be ventilated by openings on the sides, back and floor of the enclosure. Each opening must have a total area of no less than 10 square inches (254 square mm).

•Plan to install the grill in a base structure that has one of the following structural details:

◊The LP cylinder valve shall be readily accessible for hand operation. A door on the enclosure to gain access to the cylinder valves is acceptable, provided it is non-locking and can be opened without the use of tools.

◊The enclosure for the LP-gas cylinder shall isolate the cylinder from the burner compartment to provide shielding from radiation, a flame barrier and protection from foreign materials such as hot drippings.

◊There shall be a minimum clearance of 2 inches (51mm) between the floor of the LP-gas cylinder enclosure and the ground.

10" (254mm) Min. to combustibles

1 1/4" (32mm) Min. to non-combustible

28 1/2" (724mm)

To finished

countertop

Junction Box

Trim frame (accessory)

 

 

 

 

 

 

 

 

 

 

Rotisserie mounting

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

bracket (factory installed)1/4"

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(6mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3/4" (19mm)

 

 

 

 

 

23 3/4" (603mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

24" (610mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

min. to any

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

material*

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

See page 8 for overall cabinet dimensions

OB36, OBS36, OB52 and OBS52Cutout Dimensions - Side View

10" (254mm) Min. to combustibles 2" (51mm) Min. to non-combustible

Junction Box

Trim frame (accessory)

1/4"

(6mm)

23" (584mm)

3/4" (19mm) 24" (610mm) Min. to any

material*

See page 8 for overall cabinet dimensions

OBSB162 Cutout Dimensions -Side View

•The design of the outdoor cooking enclosure must allow the LP-gas cylinder to be connected, disconnected and the connections inspected and tested outside the cylinder enclosure.

•Connections which may be disturbed when installing the cylinder in the enclosure can be leak tested inside the enclosure.

•Internal mounting means shall be provided on the outdoor gas grill for mounting the LP-gas supply cylinder. If the outdoor grill is not in use, the gas must be turned off at the supply cylinder.