Dacor RR30NFS, RR30NIFS, RR30NIS Countertop, 1 5/8 (41.1 cm) max. thickness, (see diagrams), 88.3 cm), Cut 3” dia. (7.6 cm) holes, at back bottom of cabinet, 93.7 cm), for ventilation, cm)

RR30NS, RR30NFS, RR30NIS, RR30NIFS

Document # PG05-009		Revised 05/23/13 Page 4/5
	Renaissance 30” Wide	PLANNING
	Electric Inductive Range	GUIDE

Cabinet Cutouts for Self-Rimming Installation (Models RR30NIS and RR30NIFS Only)

Countertop

1 5/8 (41.1 cm) max. thickness

(see diagrams)

34 3/4”
88.3 cm)
to	Cut 3” dia. (7.6 cm) holes
36 7/8”	at back bottom of cabinet
93.7 cm)	for ventilation.

Provide ventilation through cabient both sides,

7 square inches min. Location may vary.

All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.

Countertop height: 34 3/4” (88.3 cm) min. 36 7/8” (93.7 cm) max.

Countertop thickness: 1 5/8” (4.1 cm) max.

■■ The self-rimming installation of the RR30NI[F]S range creates a “built-in” look where the range trim overlaps the countertop on both sides and in back.

■■ IMPORTANT: When installing the range in this configuration, ventilation must be provided to allow for cooling of the ranges internal components. See diagram, left.

■■ Observe all vertical cabinet clearances on page 3/5.

■■ On self-rimming installations when sliding the range into position, it will stop when the rear of the control panel or side panels contact the notches toward the front of the countertop.

1” min. (2.6 cm)	Rear wall or	3/8” min. (9.5 mm)
to any combustibles
	countertop edge
above counter both sides		countertop overhang

	24		5/8”
						29 1/4” (74.3 cm)
(62.5 cm)
					countertop opening
		max.					30 1/16” (76.2 cm)
							cabinet opening
							below countertop
							Notch countertop
				t		o width of cabinets
								Cabinet face
Countertop front						below countertop

Top View - Slide-In, Self-Rimming Installation,

3” Side Panels Installed

20”

20” (50.8 cm)

(50.8 cm) to 23”

(58.4 cm)

1” min. (2.6 cm)	Rear wall or	3/8” min. (9.5 mm)
to any combustibles
	countertop edge
above counter both sides		countertop overhang

	24		5/8”					23”
					29 1/4” (74.3 cm)
(62.5 cm)							(58.4		cm)
					countertop opening
		max.			30 1/16” (76.2 cm)*
					cabinet opening
					below countertop
					Notch countertop
				to width of cabinets
						Cabinet face
Countertop front					below countertop

Top View - Slide-In, Self-Rimming Installation,

3” Side Panels Removed

*To create a “built-in look” on the front of the cabinet, this dimension may be changed to 29 1/4” (74.3 cm), with the width at the notches remaining 30 1/16”. This configuration is only for models RR30NIS and RR30NIFS with side panels behind door removed.

All specifications subject to change without notice. www.dacor.com Phone: (800) 793-0093