Dacor RR30NFS, RR30NIFS, RR30NIS Countertop 1 5/8 (41.1 cm), max. thickness, (88.3 cm), (93.7 cm), Provide ventilation through, cabient both sides, 7 square inches min, Location may vary

RR30NS, RR30NFS, RR30NIS, RR30NIFS

Document # PG05-009		Revised 05/23/13 Page 5/5
	Renaissance 30” Wide	PLANNING
	Electric Inductive Range	GUIDE

Cabinet Cutouts for Self-Rimming Installation (Models RR30NIS and RR30NIFS Only)

Countertop 1 5/8 (41.1 cm)

max. thickness

(see diagrams)

34 3/4”
(88.3 cm)
to	Cut 3” dia. (7.6 cm) holes
36 7/8”	at back bottom of cabinet
(93.7 cm)	for ventilation.
	Provide ventilation through
	cabient both sides,
	7 square inches min.
	Location may vary.

All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.

Countertop height: 34 3/4” (88.3 cm) min. 36 7/8” (93.7 cm) max.

Countertop thickness: 1 5/8” (4.1 cm) max.

■■ Trim kit PN ATKR30SR is required for proper installation of a raised vent with this range.

■■ The self-rimming installation of the RR30NI[F]S range and ERV30[15] raised vent create a “built-in” look where the range trim overlaps the countertop on both sides and the raised vent trim overlaps the countertop in back. The ATKR30SR trim kit, installed on the back of the range, will cover the front of the raised vent chassis.

■■ IMPORTANT: When installing the range in this configuration, ventilation must be provided to allow for cooling of the ranges internal components. See diagram, left.

■■ Observe all vertical cabinet clearances on page 3/5.

■■ A self-rimming countertop configuration is required for raised vent installation. On installations with a raised vent, when sliding the range into position, it will stop when the rear of the control panel or side panels contact the notches toward the front of the countertop.

1” min. (2.6 cm)	Rear wall or	3/8” min. (1.0 cm)
to any combustibles
	countertop edge
above counter both sides		countertop overhang

27 1/2” (69.9 cm) raised vent opening

		25”
						29 1/4” (74.3 cm)
(63.5			cm)
					countertop opening
	max.						30 1/16” (76.2 cm)
							cabinet opening
							below countertop
							Notch countertop
				t		o width of cabinets
								Cabinet face
Countertop front				below countertop

2 5/8” (6.7 cm)

20 3/8”

20 3/8” (51.8 cm)

(51.8 cm) to

23 3/8”

(59.4 cm)

Top View - Downdraft ERV30[15] with Slide-In, Self-Rimming Installation, 3” Side Panels Installed

1” min. (2.6 cm)

Rear wall or

3/8” min. (1.0 cm)

to any combustibles

countertop edge

above counter both sides

countertop overhang

(6.7 cm)

27 1/2” (69.9 cm)

2 5/8”

raised vent opening

Top View - Downdraft ERV30[15] with

Slide-In, Self-Rimming Installation,

3” Side Panels Removed

25”

23

3/8”

29 1/4” (74.3 cm)

(63.5

cm)

(59.4 cm)

countertop opening

max.

30 1/16” (76.2 cm)*

cabinet opening

* To create a “built-in look” on the front of the cabinet, this

below countertop

dimension may be changed to 29 1/4” (74.3 cm), with the

Notch countertop

width at the notches remaining 30 1/16”. This configuration

t

o width of cabinets

is only for models RR30NIS and RR30NIFS with side

Cabinet face

panels behind door removed.

Countertop front

below countertop

All specifications subject to change without notice. www.dacor.com Phone: (800) 793-0093