Pairing |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
To make installation easier | Back of unit |
|
|
|
|
| Power Button | |||||||
it is recommended to pair |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
units ‘A’ and ‘B’ before |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
mounting. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
On a flat surface push the |
| Screws |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| ||||||
power button (Figure |
|
|
|
|
|
|
|
|
|
|
|
| Screws | |
on ‘A’ then push the power |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
button on ‘B’. Laying the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
units flat on counter or |
|
|
|
|
|
|
| Figure | ||||||
table, line up the infrared |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
light holes (Figure |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The units will then pair. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
You will see lights flashing |
|
|
| Place units 6 to 12 inches | ||||||||||
during this process. Leave |
|
|
|
| apart for pairing | |||||||||
the units in place for one |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
minute to make sure this |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
process is complete. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Once paired, test them by |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
completely blocking all |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
3 holes (2 infrared light |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
holes and indicator hole |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
shown in Figure |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Unit should send a signal |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
to the |
|
|
|
|
|
|
| Figure | ||||||
sound an alert. Unit will |
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
only alert if all 3 holes are |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
completely blocked for at | Front of unit |
|
|
|
|
|
|
|
| |||||
least 100ms. If an object |
|
|
|
|
|
|
|
| ||||||
|
|
|
|
| Indicator Hole | |||||||||
passes through the beam |
|
|
|
|
| |||||||||
Infrared Light Hole |
|
|
| Infrared Light Hole | ||||||||||
|
|
| ||||||||||||
faster than that it will not |
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
be detected. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
‘A’ unit contains the radio
transmitter module. The ‘A’ unit transmitter module is factory set to
match the zone 2 setting
of the
the code setting unless it is needed to avoid interference or a different zone is desired. Be careful
when opening this unit to avoid damaging any internal components or wires.
‘B’ unit contains no user serviceable parts. It is not recommended to open this unit.
3