ELECTRICAL REQUIREMENTS

This range must be properly installed and grounded by a qualified technician in accordance with the National Electrical Code ANSI/NFPA No. 70 - latest edition1 - and Local Electrical Code requirements.

This range must be connected by means of “Permanent Wiring” or “Power Supply Cord Kit” to the proper electrical voltage and frequency as specified on the model/serial rating plate.

If using a power supply cord, the plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

If using a direct wire connection, this range must be connected to a grounded metal, permanent wiring system; or an equipment-ground conductor must be run with the circuit conductors and connected to the equipment-ground terminal or lead on the range.

When installing Permanent Wiring, do not leave excess wire in range compartment. Excess wire in the range compartment may alloy the Rear Access Cover to be replaced properly and could create a potential electrical hazard if wires become pinched. Connect only as instructed under “Permanent Wire Connections”. When using flexible conduit or range cable use flex connector or range cable strain relief. NOTE: USE COPPER OR ALUMINUM CONDUCTORS

To remove the Rear wire cover is necessary to follow these instructions:

1.Remove the main top from the range

2.Remove the screw A located as is showed on Figure 1

3.Remove the screws B and C located on Rear wire cover as is showed on Figure 2

4.Take the cover off from the range

To replace the Rear wire cover proceed in reverse. Make sure the cover is fully engaged.

screw A

 

Remove the

 

screws B and C

Figure 1

Figure 2

a. MODELS WITH FACTORY CONNECTED POWER SUPPLY CORD

Some models may be equipped with a factory connected four (4)-conductor power supply cord. It is to be used when the appliance will be installed where grounding through the neutral conductor is prohibited.

1Copies of standards listed may be obtained from: National Fire Protection Association Batterymarch Park

Quincy, Massachusetts, 02269

Page 35 Page 37
Page 36
Image 36
Danby DER2009W installation instructions Electrical Requirements
Page 35 Page 37

DER2009W specifications

The Danby DER2009W is a sleek and efficient portable air conditioner designed to provide optimal cooling in any living space. With a cooling capacity of 9,000 BTUs, this unit is perfect for cooling smaller rooms up to approximately 350 square feet. Its compact design makes it easy to move from one room to another, ensuring comfort is always within reach.

One of the main features of the DER2009W is its high efficiency. It boasts an Energy Efficiency Ratio (EER) of 12.1, which means it consumes less energy while delivering powerful cooling performance. This can lead to reduced energy bills, making it an environmentally friendly choice for consumers looking to lower their carbon footprint.

The air conditioner comes equipped with multiple cooling and fan speeds, allowing users to customize their comfort. The three fan speeds and three cooling settings ensure that you can fine-tune the airflow and temperature according to your preferences. Additionally, the unit features a programmable thermostat, which allows users to set specific temperature levels for different times of the day, enhancing energy efficiency.

The DER2009W employs modern technologies to enhance the user experience. It includes an easy-to-use digital interface with a remote control, allowing for convenient adjustments from anywhere in the room. The sleep mode feature automatically adjusts the temperature during nighttime hours for increased comfort while minimizing energy consumption. Furthermore, the 24-hour timer provides flexibility, allowing users to set the unit to turn on or off at designated times.

Another significant characteristic of the Danby DER2009W is its low noise operation. With an indoor noise level measuring around 53 dB, it runs quietly in the background, making it suitable for use in bedrooms, offices, or other quiet environments.

Additionally, the unit includes a built-in dehumidifier function, capable of removing excess humidity from the air, which is particularly beneficial during hot and humid summer months.

Overall, the Danby DER2009W combines efficiency, convenience, and advanced features, making it an excellent choice for those in need of a portable air conditioning solution. Its modern design and user-friendly controls ensure a comfortable environment, while its energy-efficient performance provides peace of mind for environmentally conscious consumers.
Top Page Image Contents