PLACING & ANCHORING - ELECTRICAL

STEP 3: PLACING & ANCHORING

Lift and place the cooktop in the opening. Be careful not to pinch the power cord or gas inlet between anything. Anchor the cooktop; ensure that the appliance is in place and level (See Fig.7).

For cabinets with side access, screw the 2 “L” shaped brackets (supplied) into the holes provided using the #10 sheet-metal screws as shown in Fig.7 cooktop. Then using the 1/4 - 20 bolt and nuts (supplied), anchor as shown.

For cabinets with no side access, first fasten the brackets to the cabinet side wall using a suitable fastener. Then drill two 5/32” dia. holes upward into the bottom of cooktop and fas- ten as shown in Fig 7. countertop.

FIG. 7

 

Side access anchoring:

Bottom access anchoring:

Cooktop

Countertop

 

777fig09

STEP 4: ELECTRICAL CONNECTIONS

POWER REQUIREMENTS:

120 VAC, 60 Hz.

7 Amp.

(Use 15 Amp. Circuit)

Always disconnect electric supply cord from the wall outlet or service disconnect before servicing this appliance. Observe all governing codes and ordinances when grounding, in absence of which, observe National Electrical Code ANSI / NFPA No. 70-1987.

RECOMMENDED GROUNDING METHOD

This appliance is factory equipped with a power supply cord with a three-prong grounding plug (with polarized parallel blades). It must be plugged into a mating grounding, type receptacle, connected to a correctly polarized 120 Volt circuit. If the circuit does not have a grounding type receptacle, it is the responsibility and obligation of the installer or user to have the existing receptacle changed to a properly grounded and polarized receptacle in accordance with all applicable local codes and ordinances by a qualified electrician. In the absence of local codes and ordinances the receptacle replace- ment shall be in accordance with the National Electrical Code.

THE THIRD PRONG SHOULD NOT, UNDER ANY CIRCUMSTANCES, BE CUT OR REMOVED (See Fig. 8). (See Fig. 9).

Receptacle Box

Cover Plate

FIG. 8

Three

Prong

Plug

Three Prong

Receptacle

5

Page 6
Image 6
DCS C-24W installation manual Placing & Anchoring Electrical, Electrical Connections, Recommended Grounding Method

C-24W specifications

The DCS C-24W is a versatile and highly capable multi-role combat aircraft designed for modern warfare. This aircraft has garnered attention for its advanced features and specifications that cater to contemporary military needs. The C-24W is primarily designed for both air-to-air and air-to-ground missions, making it a formidable asset in any air force.

One of the main features of the C-24W is its powerful propulsion system, which consists of twin turbofan engines that provide exceptional speed and agility. The aircraft is capable of quick ascents and high-speed maneuvers, enabling it to evade enemy threats while engaging in combat. The engine design also allows for reduced fuel consumption, which translates to a longer operational range and increased mission versatility.

The C-24W boasts a cutting-edge avionics suite, integrating advanced digital fly-by-wire technology, allowing for precise control and enhanced safety. The cockpit is equipped with a state-of-the-art digital display system that provides pilots with real-time data on aircraft systems, terrain mapping, and enemy targets. The integration of artificial intelligence assists in combat decision-making, improving situational awareness and response time.

One of the standout characteristics of the C-24W is its stealth capabilities. The aircraft features a low observable design, which minimizes its radar signature, enabling it to conduct missions deep into enemy territory without being detected. This strategic advantage is further enhanced by its electronic warfare systems, capable of jamming enemy radar and communication systems, ensuring that the aircraft remains undetected while carrying out its objectives.

For armament, the C-24W can carry a diverse range of munitions, including air-to-air missiles, precision-guided bombs, and a variety of other ordinance types. This flexibility allows the aircraft to adapt to different mission requirements, making it effective in both air superiority and ground attack roles.

In terms of survivability, the C-24W is equipped with advanced countermeasure systems that provide protection against enemy missiles and fire. These advanced systems enhance not only the aircraft's longevity but also the success of the missions it undertakes.

Overall, the DCS C-24W is an impressive and sophisticated aircraft that reflects modern technological advancements. Its combination of speed, stealth, advanced avionics, and extensive weaponry makes it a critical component for any air combat strategy, ready to meet the challenges of today’s evolving battlefield.