Dell E2011HC appendix Common Problems, Common Symptoms, What You Experience, Possible Solutions

To run the built-in diagnostics:

1.Ensure that the screen is clean (no dust particles on the surface of the screen).

2.Unplug the video cable(s) from the back of the computer or monitor. The monitor then goes into the self-test mode.

3.Press and hold the Button 1 and Button 4 on the front panel simultaneously for 2 seconds. A gray screen appears.

4.Carefully inspect the screen for abnormalities.

5.Press the Button 4 on the front panel again. The color of the screen changes to red.

6.Inspect the display for any abnormalities.

7.Repeat steps 5 and 6 to inspect the display in green, blue, black, white screens.

The test is complete when the white screen appears. To exit, press the Button 4 again.

If you do not detect any screen abnormalities upon using the built-in diagnostic tool, the monitor is functioning properly. Check the video card and computer.

Common Problems

The following table contains general information about common monitor problems you might encounter and the possible solutions.

Common Symptoms	What You Experience		Possible Solutions
No Video/Power LED off	No picture	•	Ensure that the video cable connecting the monitor and the computer is properly
			connected and secure.
		•	Verify that the power outlet is functioning properly using any other electrical equipment.
		•	Ensure that the power button is depressed fully.
		•	Ensure that the correct input source is selected via the Input Source Select button.
No Video/Power LED on	No picture or no brightness	•	Increase brightness & contrast controls via OSD.
		•	Perform monitor self-test feature check.
		•	Check for bent or broken pins in the video cable connector.
		•	Run the built-in diagnostics.
		•	Ensure that the correct input source is selected via the Input Source Select button.
Poor Focus	Picture is fuzzy, blurry, or	•	Perform Auto Adjust via OSD.
	ghosting	•	Adjust the Phase and Pixel Clock controls via OSD.
		•	Eliminate video extension cables.
		•	Reset the monitor to Factory Settings.
		•	Change the video resolution to the correct aspect ratio (16:9).
Shaky/Jittery Video	Wavy picture or fine movement	•	Perform Auto Adjust via OSD.
		•	Adjust the Phase and Pixel Clock controls via OSD.
		•	Reset the monitor to Factory Settings.
		•	Check environmental factors.
		•	Relocate the monitor and test in another room.
Missing Pixels	LCD screen has spots	•	Cycle power on-off.
		•	Pixel that is permanently off is a natural defect that can occur in LCD technology.
		•	For more information on Dell Monitor Quality and Pixel Policy, see Dell Support site at:
			support.dell.com.
Stuck-on Pixels	LCD screen has bright spots	•	Cycle power on-off.
		•	Pixel that is permanently off is a natural defect that can occur in LCD technology.
		•	For more information on Dell Monitor Quality and Pixel Policy, see Dell Support site at:
			support.dell.com.
Brightness Problems	Picture too dim or too bright	•	Reset the monitor to Factory Settings.
		•	Auto Adjust via OSD.
		•	Adjust brightness & contrast controls via OSD.
Geometric Distortion	Screen not centered correctly	•	Reset the monitor to Factory Settings.
		•	Auto Adjust via OSD.
		•	Adjust Horizontal Position & Vertical Position controls via OSD.
		NOTE: When using DVI-D input, the positioning adjustments are not available.
Horizontal/Vertical Lines	Screen has one or more lines	•	Reset the monitor to Factory Settings.
		•	Perform Auto Adjust via OSD.
		•	Adjust Phase and Pixel Clock controls via OSD.
		•	Perform monitor self-test feature check and determine if these lines are also in self-test
			mode.
		•	Check for bent or broken pins in the video cable connector.
		•	Run the built-in diagnostics.
		NOTE: When using DVI-D input, the Pixel Clock and Phase adjustments are not available.
Synchronization Problems	Screen is scrambled or appears	•	Reset the monitor to Factory Settings.
	torn	•	Perform Auto Adjust via OSD.
		•	Adjust Phase and Pixel Clock controls via OSD.
		•	Perform monitor self-test feature check to determine if the scrambled screen appears in
			self-test mode.
		•	Check for bent or broken pins in the video cable connector.
		•	Restart the computer in the safe mode.
Safety Related Issues	Visible signs of smoke or	•	Do not perform any troubleshooting steps.
	sparks	•	Contact Dell immediately.
Intermittent Problems	Monitor malfunctions on & off	•	Ensure that the video cable connecting the monitor to the computer is connected
			properly and is secure.
		•	Reset the monitor to Factory Settings.
		•	Perform monitor self-test feature check to determine if the intermittent problem occurs in
			self-test mode.
Missing Color	Picture missing color	•	Perform monitor self-test feature check.