Installation
Using Your Dishwasher
Positioning the Appliance
ŸPosition the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that can be positioned either to the right or the left sides to facilitate proper installation.
Levelling
ŸOnce the appliance is positioned for levelling, the height of the dishwasher may be altered via adjustment of the screwing level of the feet. In any case, the appliance should not be inclined more than 2 °.
AquaStop Anti-Flood Protection
ŸYour dishwasher is fitted with an AquaStop anti- flood protection system. This system consists of a solenoid safety shut off valve which in the unlikely event of a leak, a float switch will signal the Solenoid to cut off the water supply. Therefore avoiding any flooding.
ŸDo not immerse the water inlet hose or the safety valve in water. There is an electrical cable for the safety valve in the
ŸIf water inlet hose or the safety valve is damaged, remove the main plug immediately.
ŸDo not enlarge or shorten the inlet hose because it contains electric parts.
ColdWater Connection
How to Connect the safety supply hose
The appliance must be connected to the water mains using new
Water pressure must be between 0.04 MPa and 1 MPa. If the pressure is below the minimum, consult our Service Department for advice.
If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear. This precaution is needed to avoid the risk of the water inlet getting blocked and damaging the appliance.
1.Pull the safety supply hose completely out from the storage compartment located at the rear of dishwasher.
2.Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fastened tightly in place.
3.Turn water fully on before starting the dishwasher.
WARNING! In order to avoid water staying in the inlet hose, please close the hydrant after using.
WARNING! A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sink has one, it is recommended that the hose be disconnected and the hole plugged.
How to disconnect the safety supply hose
1.Turn off the water.
2.Unscrew the safety supply hose from the faucet.
FORGETTO ADD A DISH?
A forgotten dish can be added at any time before the detergent cup opens.
1.Press the Start/Pause button.
2.Open the door a little to stop the washing.
3.After the spray arms stop working, you can open the door completely.
4.Load the forgotten dishes.
5.Close the door.
6.Press the Start/Pause button, the dishwasher will start running again after 10 seconds.
WARNING! It is dangerous to open the door when washing, because the hot water may scald you.
ATTHE END OFTHEWASH CYCLE
When the working cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then stop. Turn off the appliance using the Power switch button, shut off the water supply and open the door of the dishwasher. Wait for a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage. They will also dry better.
Switch off the Dishwasher
The program light is on but is not blinking, only in this case the programme has ended.
1.Switch off the dishwasher by pressing Power button.
2.Turn off the water tap.
Open the door carefully
Hot dishes are sensitive to knocks. The dishes should be allowed to cool down around 15 minutes before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. Dishes will be cooler and the drying will be improved.
Unloading the Dishwasher
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper Basket onto the dishes in the lower one.
Page 8 | Page 21 |
