Installation
ColdWater Connection
How to Connect the safety supply hose
The appliance must be connected to the water mains using new
AquaStop Anti-Flood Protection
Ÿ Your dishwasher is fitted with an AquaStop anti- |
flood protection system. This system consists of a |
solenoid safety shut off valve which in the unlikely |
event of a leak, a float switch will signal the Solenoid |
to cut off the water supply. Therefore avoiding any |
Using Your Dishwasher
CONTROL PANEL
1 | 2 | 3 | 4 | 5 | 6 |
Water pressure must be between 0.04 MPa and 1 MPa. If the pressure is below the minimum, consult our Service Department for advice.
If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear. This precaution is needed to avoid the risk of the water inlet getting blocked and damaging the appliance.
1.Pull the safety supply hose completely out from the storage compartment located at the rear of dishwasher.
2.Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fastened tightly in place.
3.Turn water fully on before starting the dishwasher.
flooding. |
Ÿ Do not immerse the water inlet hose or the safety |
valve in water. There is an electrical cable for the |
safety valve in the |
Ÿ If water inlet hose or the safety valve is damaged, |
remove the main plug immediately. |
Ÿ Do not enlarge or shorten the inlet hose because it |
contains electric parts. |
1Power button: To turn on/off the power supply.
2Menu Button: Press the Menu button, you can select or set programs, delay time, option functions, alternative wash and languages.
Menu Sequences: Program selection Delay time setting Option functions setting Alternative wash function selection Language setting
3OK Button: Confirm the menu selection after pressing the button
4
5‘+’ Button: Move to the left. Press the button once the menu moves to the next item on the right.
6Display Screen: To display program time, delay time, washing stages, error codes, program names, Languages, alternative wash, optional functions and using information etc;
The safety supply hose consists of the double walls. The hose's system guarantees its intervention by blocking the flow of water in case of the supply hose breaking and when the air space between the supply hose itself and the outer corrugated hose is full of water.
WARNING! In order to avoid water staying in the inlet hose, please close the hydrant after using.
WARNING! A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sink has one, it is recommended that the hose be disconnected and the hole plugged.
How to disconnect the safety supply hose
1.Turn off the water.
2.Unscrew the safety supply hose from the faucet.
Page 10
Quick operation guideline:
NOTES
1.When a selected program (and any other functions) is finished, all of the settings will be recorded by the system. The next time you wash, you just need press the power and Ok buttons to start the same washing settings as the last time. The language setting will be recorded immediately after you press the OK button.
2.If your machine rinse aid was previously used up, the display screen will show add rinse aid information when you press the power button. This will remind you to refill the rinse aid. However you can still keep using the machine following the same operations as above by pressing the MENU button to go ahead.
3.When the settings are done, the display screen will show "please close the door". The machine will start to work after the door is closed.
MENU DESCRIPTION
1.Program Selection:
The top line displays: Programmes
The bottom line displays: program names and washing time.
Default program is: Normal.
Press + or - button to change the programs, programs are: Auto, Intensive, Heavy, Normal, Glass, 60min, Rapid and Soak.
2.Delay time setting: Can delay the washing time from
3.Optional functions setting: Optional functions: Extra Dry, Express and Power wash, default setting is off, means no optional function is selected.
Extra drying: An increased temperature during the final rinse to increase drying performance. There is a slight increase in the energy consumption. (This function can only be used with programs Intensive, Heavy, Normal, Glass and 1 Hour).
Express: This function can reduce the washing time. Water and energy consumption are slightly increased. (This function can only be used with programs Intensive, Heavy, Normal and Glass).
Power Wash: This function can wash very soiled pots and pans. The temperature of water will be increased during the washing cycle. (This function can only be used with programs Intensive, Heavy, Normal, Glass and 1 Hour).
3.Alternative wash function selection: Select both sprayers running, upper sprayer running only or lower sprayer running only.
4.Language setting: Languages that can be selected are -
Page 23
