DeLonghi DEDW97FI manual Using Your Dishwasher

Installation

ColdWater Connection

Ÿ Connect the cold water supply hose to a threaded

3/4(inch) connector and make sure that it is

fastened tightly in place.

Ÿ If the water pipes are new or have not been used for

an extended period of time, let the water run to

make sure that the water is clear. This precaution is

needed to avoid the risk of the water inlet getting

blocked and damaging the appliance.

How to install the mechanical Aqua Stop Hose

ŸMechanical Aqua Stop Hose preparation.

1

Inlet valve

Using Your Dishwasher

CONTROL PANEL

OFF

ON

1 2 DELAY PROG.

WARNING!

In order to avoid water staying in the inlet hose, please close the hydrant after using. (Not applicable to appliances without aqua-stop.)

Drain Hose Connection

ŸInsert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it run into the sink, making sure to avoid bending or crimping it. Use the special plastic support that comes with the appliance . The top of the hose must be at a height between 40 and 100cm. The free end of the hose must not be immersed in water to avoid the back flow of it.

Mechanical Aqua Stop hose

ŸSnap-fit the inlet valve and rotate the clamp ring to fix the hose.

2

Clamp ring

12

1ON/OFF Button: To turn on/off the power supply.

2Power on light: Becomes lit when the Power ON/OFF button is pressed down.

3Half Load Button: To select Half load functions. (Half load function means that the lower spray arm does not run, so you should load the upper basket only).

TURNING ONTHE APPLIANCE

Starting a wash cycle:

1.	Draw out the lower and upper basket, load the
	dishes and push them back. It is recommended to
	load the lower basket first, then the upper one (see
	the section entitled “Loading the Dishwasher”).
2.	Pour in the detergent (see Page 13).
3.	Insert the plug into the socket. The power supply is
	220-240 VAC / 50 HZ, the specification of the
	socket is 10A 250VAC. Make sure that the water
	supply is turned on to full pressure.
4.	Open the door, press the ON/OFF button, and the
	ON/OFF light will turn on.
5.	Press the program button to select your desired

3 4 5 6

4Delayed Start Button: Press this button to set the delayed hours for washing. You can delay the start of washing up to 24 hours. One press on this button delays the start of washing by one hour.

5Display window: Displays the delay time, running indicator, fault codes and etc.

6Program Button: Press this button to select the desired washing program.

CHANGETHE PROGRAM

Premise:

1.A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the detergent may have already been released, and the appliance may have already drained the wash water.

If this is the case, the detergent dispenser must be refilled (see the section entitled "Adding Detergent").

2.Open the door, press the PROG. button more than three seconds to cancel the program, then you can change the program to the desired cycle setting. Then, close the door.

DISHWASHER

Inlet pipe	Drain pipe
connector	connector

SINK

POWER	Min 400mm
OUTLET

Max 1000mm

WARNING!

DO NOT BEND IN ANY WAY!

	wash cycle.
6.	Close the dishwasher door with a little force to
	ensure the door is closed properly. A click can be
	heard when the door is closed perfectly.
7.	When the washing cycle is complete, you can shut
	off the switch by pressing the ON/OFF button.

NOTE:

If you open the door during a wash cycle, the machine will pause. The LED Display Window will stop blinking and the buzzer will sound every minute unless you close the door. After you close the door, the dishwasher will continue working after 10 seconds.

If display window shows error codes after a warning sound (see page 29 for “ERROR CODES"), that indicates the machine is out of order, please turn off the main power and water supply before calling for service.

FRONT VIEW Min 100mm

Page 10 Page 23