Manuals / Delta / Computer Equipment / Network Router

Delta 43-505 Unpacking And Cleaning, Extension Cords, Foreword, Fig. D, Operating Instructions

Models: 43-505

1 18

Download 18 pages 30.78 Kb

Page 5

EXTENSION CORDS

EXTENSION CORDS

Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D, shows the correct gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere		Total Length	Gauge of
Rating	Volts	of Cord in Feet	Extension Cord

0-6	120	up to 25	18 AWG
0-6	120	25-50	16 AWG
0-6	120	50-100	16 AWG
0-6	120	100-150	14 AWG
6-10	120	up to 25	18 AWG
6-10	120	25-50	16 AWG
6-10	120	50-100	14 AWG
6-10	120	100-150	12 AWG

10-12	120	up to 25	16 AWG
10-12	120	25-50	16 AWG
10-12	120	50-100	14 AWG
10-12	120	100-150	12 AWG

12-16	120	up to 25	14 AWG
12-16	120	25-50	12 AWG
12-16	120	GREATER THAN 50 FEET NOT RECOMMENDED

Fig. D

OPERATING INSTRUCTIONS

FOREWORD

Delta Model 43-505 Router / Shaper is an economical alternative to the production wood shaper. The Router / Shaper has a powerful, 9 amp, induction-type, ball bearing motor for long-lasting trouble free operation. The Router / Shaper also has a thermal overload protection which prevents motor overload.

UNPACKING AND CLEANING

Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste wax.

NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT

PRODUCTION MODEL. ALL OTHER ILLUSTRATIONS ARE REPRESENTATIVE

ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR

ACCESSORIES.

5

Image 5

Delta 43-505 Unpacking And Cleaning, Extension Cords, Foreword, Notice The Manual Cover Photo Illustrates The Current

Contents

For Parts, Service, Warranty or other Assistance please call 1-800-223-7278 In Canada callRouter / Shaper INSTRUCTION MANUALTechnical Service Manager Delta Machinery 4825 Highway 45 North GENERAL SAFETY RULESJackson, TN 2. KEEP GUARDS IN PLACE and in working orderRefer to them often and use them to instruct others ADDITIONAL SAFETY RULES FOR FOR THE ROUTER/SHAPERSAVE THESE INSTRUCTIONS MOTOR SPECIFICATIONS POWER CONNECTIONSGROUNDING INSTRUCTIONS Fig. AONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR ACCESSORIES UNPACKING AND CLEANINGEXTENSION CORDS FOREWORDASSEMBLING ROUTER/SHAPER TO ACCESSORY STAND ASSEMBLYASSEMBLING ACCESSORY STAND ASSEMBLING OVERHEAD CUTTER GUARD BRACKET ASSEMBLING AND INSTALLING FENCE ASSEMBLY AND DUST CHUTED B C H N MLOCKING SWITCH IN THE “OFF” POSITION OPERATING CONTROLS AND ADJUSTMENTSFASTENING ROUTER/SHAPER TO SUPPORTING SURFACE ASSEMBLING TABLE INSERTRAISING AND LOWERING SPINDLE FENCE ADJUSTMENTSOVERLOAD PROTECTION WRENCH STORAGE ADJUSTING SPINDLE 90 DEGREES LEFT AND RIGHT TO THE TABLESEE-THRU CUTTER GUARD ADJUSTING TABLE 90 DEGREES FRONT AND BACK TO THE SPINDLE STARTING PIN INSTALLING ROUTER BITS1. DISCONNECT MACHINE FROM POWER SOURCE 1. DISCONNECT MACHINE FROM POWER SOURCE INSTALLING OVERHEAD CUTTER GUARDINSTALLING ACCESSORY SHAPER SPINDLE ROUTING OR SHAPING WITH COLLARS AND STARTING PIN ROUTING OR SHAPING WHEN USING THE FENCE AS A GUIDEOPERATION AGAINST THE ROTATION OF THE CUTTER POSITION OF COLLARSSTARTING PIN Two Year Limited Warranty ACCESSORIESPARTS, SERVICE OR WARRANTY ASSISTANCE