9)Byte 128 to 255 had been set hex 00.
Digital Diagnostic Monitoring Interface
Alarm and Warning Thresholds (2-Wire Address A2h)
|
| Address |
| # |
| Name |
| Value (Dec.) |
| Unit |
|
| Note |
|
|
|
| Bytes |
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2 |
| Temp High Alarm | TC (MAX.)+15 | ℃ | 1 |
| |||||||
2 |
| Temp Low Alarm | TC (MIN.) |
|
|
|
|
| ||||||
2 |
| Temp High Warning | TC (MAX.)+10 |
|
|
|
|
| ||||||
2 |
| Temp Low Warning | TC (MIN.)+10 |
|
|
|
|
| ||||||
2 |
| Voltage High Alarm | Vcc+5% | Volt |
|
|
|
| ||||||
| 2 |
| Voltage Low Alarm |
|
|
|
|
| ||||||
|
| 2 |
| Voltage High Warning | Vcc+3% |
|
|
|
|
| ||||
|
| 2 |
| Voltage Low Warning |
|
|
|
|
|
| ||||
2 |
| Bias High Alarm | IOP*2+20 | mA | 2 |
| ||||||||
2 | Bias Low Alarm |
|
|
|
|
| ||||||||
2 |
| Bias High Warning | IOP *2+10 |
|
|
|
|
| ||||||
2 |
| Bias Low Warning | IOP |
|
|
|
|
| ||||||
2 |
| TX Power High Alarm | P+3 | dBm |
|
| 3 |
| ||||||
| 2 |
| TX Power Low Alarm |
|
|
|
|
| ||||||
|
| 2 |
| TX Power High Warning | P+2 |
|
|
|
|
| ||||
|
| 2 |
| TX Power Low Warning |
|
|
|
|
|
| ||||
2 |
| RX Power High Alarm | P0+3 | dBm | 4 |
| ||||||||
2 |
| RX Power Low Alarm |
|
|
|
|
| |||||||
2 |
| RX Power High Warning | P0+2 |
|
|
|
|
| ||||||
2 |
| RX Power Low Warning | PS |
|
|
|
|
| ||||||
16 |
| Reversed |
|
|
|
|
|
|
| |||||
36 |
| External Calibration Constants |
|
|
|
|
|
|
| |||||
3 |
| Reversed |
|
|
|
|
|
|
| |||||
95 | 1 |
| Checksum |
|
|
|
|
| 5 |
| ||||
2 | Real Time Temperature |
|
|
|
|
|
|
| ||||||
2 | Real Time Supply Voltage |
|
|
|
|
|
|
| ||||||
2 | Real Time Tx Bias Current |
|
|
|
|
|
|
| ||||||
2 | Real Time Tx Optical Power |
|
|
|
|
|
|
| ||||||
2 | Real Time Rx Received Power |
|
|
|
|
|
|
| ||||||
4 |
| Reserved |
|
|
|
|
|
|
| |||||
110 | 1 |
| Optional Status/ Control Bits |
|
|
|
|
| 6 |
| ||||
111 | 1 |
| Reserved |
|
|
|
|
|
|
| ||||
8 |
| Optional Set of Alarm and Warning |
|
|
|
|
| 7 |
|
Notes:
1)TC: Case Operating temperature
2)IOP: Operating current at room temperature. The min. setting current is 0 mA.
3)P: Operating optical power of transmitter at room temperature.
4)P0: Overload optical power of receiver
PS: Sensitivity optical power of receiver
5) Byte 95 contains the low order 8bits of sum of bytes
11 | 2008/1/23 |
| Rev. 6G |
DELTA ELECTRONICS, INC. | www.deltaww.com |