ENGLISH

Others

Troubleshooting

If a problem should arise, first check the following:

1.Are the connections correct ?

2.Have you operated the player according to the Operating Instructions ?

If this unit is not operating properly, check the items listed in the table below. Should the problem persist, there may be a malfunction. Disconnect the power immediately and contact your store of purchase.

Symptom

 

Measures

 

Cause

Page

Disc tray does not open.

• The power is not on.

 

• Turn on the power.

7

 

 

 

 

“NO DISC” is displayed

• The disc is not properly loaded.

• Reload the disc.

2, 3

even though a disc is loaded.

 

 

 

 

 

 

 

 

 

 

“00 00 : 00” is displayed

• The loaded disc is not a CD.

 

• Load a CD.

2

even though a disc is loaded.

 

 

 

 

 

 

 

 

 

 

Disc is not played when play

• The disc is dirty or scratched.

 

• Wipe the dirt off the disc or replace

3

button is pressed.

 

 

 

the disc.

 

 

 

 

 

No sound is produced or

• The output cables are not properly

• Check the connections.

6

sound is distorted.

connected to the amplifier.

 

 

 

 

• The amplifier’s function setting or

• Check the amplifier’s function and

–

 

adjustments are not right.

 

controls and adjust as necessary.

 

 

 

 

 

 

 

No digital signals are output.

• The

connection cables are

not

• Check the connections.

6

 

properly connected.

 

 

 

 

 

 

 

 

Specific section of the disc

• The disc is dirty or scratched.

 

• Wipe the dirt off the disc or replace

3

cannot be played properly.

 

 

 

the disc.

 

 

 

 

 

 

 

Programmed playback is not

• The

tracks have not

been

• Program properly.

8

possible.

programmed properly.

 

 

 

 

 

 

 

A CD-R or CD-RW disc

• The disc has not been finalized.

• Finalize the disc then play it.

2

cannot be played.

• The recording conditions are bad or

• Use a properly recorded disc.

2

 

the quality of the disc itself it poor.

 

 

 

 

 

 

 

Set does not operate

• The batteries are spent.

 

• Replace the batteries with new

3

properly when remote

 

 

 

ones.

 

control unit is operated.

• The remote control unit is too far

• Move the remote control unit closer

3

 

from the set.

 

to the set.

 

 

 

 

 

 

 

Specifications

¢ Audio performance

• Analog output

 

Channels:

2 channels

Playable frequency range:

2 Hz ~ 20 kHz

S/N:

105 dB

Dynamic range:

98 dB

Harmonic distortion:

0.003 % (1 kHz)

Wow & flutter:

Below measurable limits

Output level:

2.0 V (10 kΩ/kohms)

Signal type:

16-bit linear PCM

Sampling frequency:

44.1 kHz

Usable discs:

Compact Disc

• Digital output

 

Optical:

–15 ~ –21 dBm

Emission wavelength:

660 nm

¢ General

Power supply:

AC 230 V, 50 Hz

Power consumption:

13 W

Maximum external dimensions:

434 (W) x 107 (H) x 279 (D) mm (including protruding parts)

Mass:

4.0 kg

¢Remote control unit (RC-1028)

Remote control type:

Infrared pulse

Batteries:

R03/AAA Type (two batteries)

External dimensions:

49 (W) x 220 (H) x 21 (D) mm

Mass:

106 g (included batteries)

* For purposes of improvement, specifications and design are subject to change without notice.

10

ENGLISH