Denon DN-780R manual 6

ENGLISH

!4Tape Transport Buttons

0 , 1	Play Button	Press to playback tape.
2	Stop Button	Press to stop the tape in any mode.
6	Fast Rewind Button	Press for fast rewind.
7	Fast Forward Button	Press for fast forwarding.
		Press the Rec/Rec Mute button ( 4 ) and Play button ( 0 , 1 )
		simultaneously to start recording. If only the Rec/Rec Mute
4	Rec/Rec Mute Button	button ( 4 ) is pressed, the deck enters the recording pause
		mode. Pressing this button in the recording pause mode will
		start Auto Rec Mute, and a 5-second silent space is recorded
		onto the tape. See page 9.
		Press this button to enter the recording pause mode from the
3	Rec Pause Button	recording or recording mute mode. This button can only be used
		during recording. See page 9.

@2Display

Deck A Tape Counter		Reverse Mode Indicator				Deck B Tape Counter
	Deck A Peak Level Meter			Deck B Peak Level Meter
Deck A Dolby NR							Deck B Dolby NR
Indicator							Indicator
Deck A Memory							Deck B Memory
Indicator							Indicator
• Synchronized Indicator	Deck A		Twin Rec		Deck B		Lights when deck B is
• Infrared Remote	Tape Transport		Indicator		Tape Transport		selected with the RC IN
Control Indicator	Indicator				Indicator		control jack.

Dubbing Speed Indicator

Lights when deck A is selected with the RC IN control jack.

!5Input Select Switch of Deck B (INPUT SELECT)

Select the audio input to the Deck B (DECK A, LINE A, LINE B).

!6Cassette Compartment Cover

If the cover is not closed completely, the tape transport buttons will remain inoperative.

!7Counter Memory Button

(COUNTER MEMO)

When this button is pressed during forward tape travel ( 1 ), fast rewinding ( 6 ) will stop automatically at the tape counter position “‚‚‚‚”.

When this button is pressed during reverse tape travel ( 0 ), fast forwarding ( 7 ) will stop automatically at the tape counter position “‚‚‚‚”. See page 11.

!9Eject Button ( 5 )

Press this button to open the cassette compartment cover. When the tape is running, press the Stop ( 2 ) button first to stop tape transport, then press the Eject ( 5 ) button.

@0Reverse Mode Button (REV. MODE)

Select the type of tape transport. The reverse

mode can be set to (one side), (continuous playback), RELAY (relay playback), CASCADE (continuous recording/playback on multiple units is possible).

@1Twin Recording Button (TWIN REC)

Pressing this button will set both deck A and B to the recording pause mode. See page 10.

@3Remote Control Sensor

(REMOTE SENSOR)

This sensor receives the infrared light transmitted from the wireless remote control unit.

This product dose not come with remote control unit.

@4Deck A, B Line Input Jacks (LINE IN)

These are unbalanced inputs using RCA type jacks.

Use them to input signals to be recorded on a tape.

@5Deck A, B Line Output Jacks (LINE OUT)

These are unbalanced outputs using RCA type jacks.

@6Deck A Line Output Select Switch

@9Cascade Control Jacks (CASCADE)

Connect these for continuous operation on multiple units.

When the REV. MODE button @0 is set to “CASCADE”, the start signal is output from this output jack once operation of Deck B is finished.

#0Serial Control Port (RS232C)

This is serial remote connector. Applicable connector : 9-pin D-sub (male) Baud rate : 9600 bps

Pin layout

Pin No.	Signal Name	I / O
1	GND	_
6	NC	_
2	TxD	O

!8Counter Reset Button

(COUNTER RESET)

Press this button to reset the tape counter to zero.

(DECK A OUTPUT SEL.)

Selects the signal to be output from the Deck A output jacks.

A : The Deck A signal is output.

A+B : Both the Deck A and Deck B signals are output.

@7Deck A Line Input Through Jacks (THRU)

The signal input to the DECK A LINE IN jacks is output unchanged.

@8External Synchronized Control Jacks (EXT. SYNC.)

Connect these for synchronized recording.

7	NC	_
3	RxD	I
8	NC	_
4	NC	_
9	NC	_
5	S. GROUND	_

6