35,000, 50,000, And 55,000 Btu/Hr H.S.I. Series

PORTABLE FORCED AIR HEATERS

SERVICE

PROCEDURES

WARNING: Never service heater while it is plugged in, op- erating, or hot. Severe burns and electrical shock can occur.

UPPER SHELL REMOVAL

1.Remove screws along each side of heater using 5/16" nut-driver. These screws attach upper and lower shells together.

2.Lift upper shell off.

3.Remove fan guard.

Upper Shell

Fan

Guard

Figure 3 - Upper Shell Removal

FAN

IMPORTANT: Remove fan from motor shaft before removing motor from heater. The weight of the motor resting on the fan could damage the fan pitch.

1.Remove upper shell (see above).

2.Use 1/8" Allen wrench to loosen set- screw which holds fan to motor shaft.

3.Slip fan off motor shaft.

4.Clean fan using soft cloth moistened with kerosene or solvent.

5.Dry fan thoroughly.

6.Replace fan on motor shaft. Place fan hub flush with end of motor shaft (see Figure 4).

7.Place setscrew on flat of shaft. Tighten setscrew firmly (40-50 inch-pounds).

8.Replace fan guard and upper shell.

Fan

Motor

Flush

Motor

Shaft

Setscrew

Figure 4 - Fan Cross Section

AIR OUTPUT, AIR INTAKE, AND LINT FILTERS

1.Remove upper shell (see Upper Shell Removal).

2.Remove filter end cover screws using 5/16" nut-driver.

3.Remove filter end cover.

4.Replace air output and lint filters.

5.Wash or replace air intake filter (see Preventative Maintenance Schedule, page 4).

6.Replace filter end cover.

7.Replace fan guard and upper shell. IMPORTANT: Do not oil filters.

Air Intake Filter

Filter End Cover

Fan Guard

Lint Filter

Air Output Filter

Figure 5 - Air Output, Air Intake, and Lint Filters

PUMP PRESSURE

ADJUSTMENT

1.Remove pressure gauge plug from filter end cover.

2.Install accessory pressure gauge (part number HA1180).

3.Start heater (see Operation, page 4). Al- low motor to reach full speed.

4.Using a flat blade screwdriver, adjust pressure. Turn relief valve to right to increase the pressure. Turn relief valve to left to decrease the pressure. Set pump pressure as follows:

35 Model: 3.0 psi

50 Model: 3.6 psi

55 Model: 3.6 psi

5.Remove pressure gauge. Replace pres- sure gauge plug in filter end cover.

Pressure

 

Gauge

 

Plug

Relief Valve

 

Figure 6 - Pressure Gauge Plug Removal

Pressure

Gauge

Figure 7 - Adjusting Pump Pressure

6

102388

Page 6
Image 6
Desa and 55 owner manual Service Procedures, Upper Shell Removal, Fan, AIR OUTPUT, AIR INTAKE, and Lint Filters

and 55 specifications

Desa and 55 are two innovative initiatives that represent the convergence of modern technology and community-focused governance. Both aim to enhance the quality of life for their respective users while promoting sustainable living and effective resource management.

Desa is centered around the concept of "smart villages," where technology is seamlessly integrated into daily life to support sustainable practices. This initiative focuses on empowering rural communities by providing access to modern services and infrastructure through a digital framework. Key features of Desa include smart agriculture, where IoT devices are utilized to monitor soil conditions and optimize water usage, thereby increasing crop yields while minimizing environmental impact. Additionally, Desa promotes renewable energy sources, encouraging communities to harness solar or wind power for local needs and reducing dependence on fossil fuels.

On the other hand, 55 is an urban-centered model aimed at enhancing city living through the use of cutting-edge technologies. It embodies a comprehensive approach to urban planning, integrating smart transportation, waste management, and energy systems. Key characteristics of 55 include a robust public transport system, which employs real-time data analytics to improve efficiency and accessibility. Smart waste management technologies ensure effective recycling processes and decrease landfill usage, thus promoting a circular economy.

Both Desa and 55 prioritize community engagement and participation. They utilize mobile applications and platforms to encourage residents to partake in localized decision-making, ensuring that the systems remain relevant to the unique needs of their users. Data privacy and security are also paramount; both initiatives adopt stringent measures to protect user information while still enabling the benefits of data analysis.

In summary, Desa and 55 represent two distinct but complementary approaches to integrating technology into community living. While Desa focuses on empowering rural areas through sustainable practices, 55 enhances urban life through smart solutions. Their commitment to innovation, community involvement, and sustainability positions both initiatives as leaders in the movement toward smarter, more resilient communities. As global challenges such as climate change and urbanization continue to evolve, models like Desa and 55 will be crucial in shaping a sustainable future.