OWNER’S MANUAL
INSTALLING
TO WALL
Continued
INSTALLING HEATER TO WALL
Marking Screw Locations
1.Determine where you will locate heater.
WARNING: Maintain minimum clearances shown in Figure 5. If you can, provide greater clear- ances from floor and joining wall.
2.Mark two mounting screw locations on wall (see Figure 5).
Attaching to Wall Anchor Method
Follow instructions below to attach mount- ing screws to hollow walls (wall areas be- tween studs) or solid walls (concrete or masonry).
1.Drill holes at marked locations using 5/16" drill bit. For solid walls (concrete or masonry), drill at least 1 1/4" deep.
2.Fold wall anchor (see Figure 6).
3.Insert wall anchor (wings first) into hole. Tap anchor flush to wall.
Placing Heater on Mounting Screws
1.Locate two keyhole slots on back panel of heater (see Figure 9).
2.Place large openings of slots over screwheads. Slide heater down until screws are in small portion of slots.
Keyhole
Slots
Figure 9 - Location Of Keyhole Slots On Back Panel Of Heater
Removing Front Panel of Heater
|
| 10 7/8" |
|
|
|
| 7 3/4" |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
| Minimum To |
|
|
|
|
|
|
|
|
| |||
| Maintain 6" |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| |||||
| Clearance |
|
|
|
|
|
|
|
|
| |||
| From Wall |
|
|
|
|
|
|
|
|
| |||
|
| Mounting |
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
| |||
WALL |
| Screw |
|
|
|
|
| ||||||
|
|
|
|
|
| Locations |
| 20 1/4" | |||||
|
|
|
|
|
|
|
|
|
| ||||
JOINING |
|
|
|
|
| Minimum To | |||||||
|
|
|
|
|
| Maintain 3" | |||||||
|
|
|
|
|
|
|
|
|
|
| |||
Clearance
From Floor
FLOOR
Figure 5 - Mounting Screw Locations
Installing Two Mounting Screws
Note: Wall anchors and mounting screws are in hardware package. The hardware pack- age is provided with heater.
Attaching to Wall Stud Mmethod
For attaching mounting screw to wall stud
1.Drill hole at marked location using 9/ 64" drill bit.
2.Insert mounting screw into wall stud.
3.Tighten screw until 1/16" space (thickness of penny) is between
screwhead and wall.
Figure 6 - Folding Anchor
4.For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings (see Figure 7). IMPORTANT: Do not hammer key! For thick walls (over 1/2" thick) or solid walls, do not pop open wings.
Thin Walls
(1/4" to 1/2" thick)
Figure 7 - Popping Open Anchor Wings For Thin Walls
5.Tighten two screws until 1/16" space (thickness of penny) is between screwheads and wall (see Figure 8).
Thin or Thick Wall (thick wall shown)
1/16" Space
Solid
Wall
Figure 8 - Tightening Anchors
1.Remove two screws near bottom corners of front panel.
2.Lift straight up on grill guard until it stops. Grill guard will slide up about 1/4".
3.Pull bottom of front panel forward, then down.
Figure 10 - Removing Front Panel Of Heater
Installing Bottom Mounting Screw
1.Locate bottom mounting hole. This hole is near bottom on back panel of heater (see Figure 11, page 8).
2.Mark screw location on wall.
3.Remove heater from wall.
Continued
103548 | 7 |
