BLUE-FLAME

VENT-FREE PROPANE/LP GAS HEATER

INSTALLATION

Continued

INSTALLING HEATER TO WALL

Mounting Bracket

Locate mounting bracket in heater carton. Remove mounting bracket from heater carton.

Figure 5 - Mounting Bracket Location

Removing Front Panel Of Heater

1.Remove two screws near bottom cor- ners of front panel.

2.Lift straight up on grill guard until it stops. Grill guard will slide up about 1/4".

3.Pull bottom of front panel forward, then down.

4.Remove cardboard packing from grill and glass (CGP20[L]B) or heat shield (RP30E).

Figure 6 - Removing Front Panel Of Heater

Methods For Attaching Mounting Bracket To Wall

Only use last hole on each end of mounting bracket to attach bracket to wall. These two holes are 16 inches apart from their centers. Attach mounting bracket to wall in one of two ways.

1.Attaching to wall stud

2.Attaching to wall anchor

Attaching to Wall Stud: This method pro- vides the strongest hold. Insert mounting screws through mounting bracket and into wall studs.

Attaching to Wall Anchor: This method allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry).

Decide which method better suits your needs. Either method will provide a secure hold for the mounting bracket.

Marking Screw Locations

1.Tape mounting bracket to wall where heater will be located. Make sure mounting bracket is level.

2.Mark screw locations on wall (see Fig- ure 7).

WARNING: Maintain minimum clearances shown in Figure 7. If you can, provide greater clear- ances from floor and joining wall.

Note: Only mark last hole on each end of mounting bracket. Insert mounting screws through these holes only.

3.Remove tape and mounting bracket from wall.

11"

16"

Min.

 

AdjoiningWall

 

Only Insert Mounting

32 1/2"

 

 

Screws Through Last

 

 

Min.

 

 

Hole On Each End

 

 

 

 

 

 

 

Floor

 

 

 

 

RP30E

 

 

 

7 1/4"

16"

 

 

 

Min.

 

 

 

AdjoiningWall

Only Insert Mounting

18 3/4"

Screws Through Last

 

Min.

 

 

Hole On Each End

 

 

 

 

 

Floor

CGP20(L)B

Figure 7 - Mounting Bracket Clearances

Attaching Mounting Bracket To Wall

Note: Wall anchors, mounting screws, and spacers are in hardware package. The hard- ware package is provided with heater.

Attaching to Wall Stud Method

For attaching mounting bracket to wall studs

1.Drill holes at marked locations using 9/64" drill bit.

2.Place mounting bracket onto wall. Line up last hole on each end of bracket with holes drilled in wall.

3.Insert mounting screws through bracket and into wall studs.

4.Tighten screws until mounting bracket

is firmly fastened to wall studs.

8

104412

Page 8
Image 8
Desa RP30E, CGP20LB, CGP20B installation manual Installing Heater to Wall

RP30E, CGP20B, CGP20LB specifications

Desa CGP20B, CGP20LB, and RP30E represent a series of versatile and robust generators designed to meet diverse power needs across various applications. These models blend advanced technology with user-friendly features, making them suitable for both residential and commercial use.

The Desa CGP20B is notable for its compact design and high-efficiency performance. It is equipped with a powerful engine that ensures reliable power output, making it ideal for backup power during outages or for powering tools at job sites. The generator features a large capacity fuel tank that allows for extended run times, making it a practical choice for extended use. Additionally, the CGP20B comes with a user-friendly control panel, which includes clearly marked outlets, making it easy to connect appliances and devices.

The CGP20LB model stands out with its low noise operation, making it one of the quieter options in the generator market. This is particularly beneficial for residential areas or during camping trips. Its lightweight design enhances portability, allowing users to transport it with ease. The unit is also equipped with a variety of safety features, including overload protection and a low oil shutoff mechanism, which helps to extend the lifespan of the generator.

On the other hand, the RP30E is designed for more heavy-duty applications. This model boasts a higher power output and is suitable for larger appliances, industrial tools, and construction sites. The RP30E incorporates advanced inverter technology, which provides clean and stable power, making it safe for sensitive electronics. Its digital display panel provides real-time monitoring of power consumption and operational status, ensuring users are always informed about the generator's performance.

All three models feature sturdy construction, ensuring durability and reliability in challenging environments. They also come with multiple outlet options, including 120V and 240V outlets, which enhances their versatility. Fuel efficiency is a key characteristic across the range, allowing users to save on operational costs while minimizing environmental impact.

In conclusion, the Desa CGP20B, CGP20LB, and RP30E generators offer an impressive array of features and technologies tailored to meet varied power requirements. Whether for residential backup, recreational use, or industrial applications, these generators deliver reliability, efficiency, and ease of use, making them valuable assets for any user.