OWNER’S MANUAL

INSTALLATION

Continued

Attaching to Wall Anchor Method

For attaching mounting bracket to hollow walls (wall areas between studs) or solid walls (concrete or masonry)

1.

Drill holes at marked locations using

 

5/16" drill bit. For solid walls (concrete

 

or masonry), drill at least 1" deep.

2.

Fold wall anchor as shown in Figure 8.

3.

Insert wall anchor (wings first) into

 

hole. Tap anchor flush to wall.

4.

For thin walls (1/2" or less), insert red

 

key into wall anchor. Push red key to

 

“pop” open anchor wings.

 

IMPORTANT: Do not hammer key!

Placing Heater On Mounting Bracket

1.Locate two horizontal slots on back panel of heater.

2.Place heater onto mounting bracket. Slide horizontal slots onto stand-out tabs on mounting bracket.

Horizontal Slots

7.Hold spacer in place with one hand. With other hand, insert mounting screw through bottom mounting hole and spacer. Place tip of screw in opening of wall anchor or drilled hole.

8.Tighten both screws until heater is firmly secured to wall. Do not over tighten.

Note: Do not replace front panel at this time. Replace front panel after making gas connections and checking for leaks (see pages 10 and 11).

 

For thick walls (over 1/2" thick) or solid

 

walls, do not pop open wings.

5.

Place mounting bracket onto wall. Line

 

up last hole on each end of bracket with

 

wall anchors.

6.

Insert mounting screws through bracket

 

and into wall anchors.

7.

Tighten screws until mounting bracket

 

is firmly fastened to wall.

Figure 8 - Folding Anchor

Figure 9 - Popping Open Anchor Wings For Thin Walls

Stand-Out Tab

Mounting Bracket

(attached to wall)

Figure 10 - Mounting Heater Onto Mounting Bracket

Installing Bottom Mounting Screws

1.Locate two bottom mounting holes. These holes are near bottom on back panel of heater (see Figure 11).

2.Mark screw locations on wall.

3.Remove heater from mounting bracket.

4.If installing bottom mounting screws into hollow or solid wall, install wall anchors. Follow steps 1 through 4 un- der Attaching To Wall Anchor Method, column 1.

If installing bottom mounting screw into wall stud, drill holes at marked lo- cations using 9/64" drill bit.

5.Replace heater onto mounting bracket.

6.Place spacers between bottom mount- ing holes and wall anchor or drilled hole.

Figure 11 - Installing Bottom Mounting Screws

Continued

104412

9

Page 8 Page 10
Page 9
Image 9
Desa CGP20LB, CGP20B, RP30E installation manual Placing Heater On Mounting Bracket, Installing Bottom Mounting Screws
Page 8 Page 10

RP30E, CGP20B, CGP20LB specifications

Desa CGP20B, CGP20LB, and RP30E represent a series of versatile and robust generators designed to meet diverse power needs across various applications. These models blend advanced technology with user-friendly features, making them suitable for both residential and commercial use.

The Desa CGP20B is notable for its compact design and high-efficiency performance. It is equipped with a powerful engine that ensures reliable power output, making it ideal for backup power during outages or for powering tools at job sites. The generator features a large capacity fuel tank that allows for extended run times, making it a practical choice for extended use. Additionally, the CGP20B comes with a user-friendly control panel, which includes clearly marked outlets, making it easy to connect appliances and devices.

The CGP20LB model stands out with its low noise operation, making it one of the quieter options in the generator market. This is particularly beneficial for residential areas or during camping trips. Its lightweight design enhances portability, allowing users to transport it with ease. The unit is also equipped with a variety of safety features, including overload protection and a low oil shutoff mechanism, which helps to extend the lifespan of the generator.

On the other hand, the RP30E is designed for more heavy-duty applications. This model boasts a higher power output and is suitable for larger appliances, industrial tools, and construction sites. The RP30E incorporates advanced inverter technology, which provides clean and stable power, making it safe for sensitive electronics. Its digital display panel provides real-time monitoring of power consumption and operational status, ensuring users are always informed about the generator's performance.

All three models feature sturdy construction, ensuring durability and reliability in challenging environments. They also come with multiple outlet options, including 120V and 240V outlets, which enhances their versatility. Fuel efficiency is a key characteristic across the range, allowing users to save on operational costs while minimizing environmental impact.

In conclusion, the Desa CGP20B, CGP20LB, and RP30E generators offer an impressive array of features and technologies tailored to meet varied power requirements. Whether for residential backup, recreational use, or industrial applications, these generators deliver reliability, efficiency, and ease of use, making them valuable assets for any user.
Top Page Image Contents