CLEANING AND MAINTENANCE
Cleaning Burner Injector Holder and Pilot Air Inlet Hole (Cont.)
Logs
Main Burner
SPECIFICATIONS
21
CLEANING AND MAINTENANCE
Continued
4.Check the injector holder located at the end of the burner tube again. Remove any large particles of dust, dirt, lint, or pet hair with a soft cloth or vacuum cleaner nozzle.
SPECIFICATIONS
Dual Burner Smoky Mountain Oak and Premium Aged Split Oak Models
| 18" Model | 24" Models | 30" Models |
Btu (Variable) | 16,000/30,000 | 20,000/39,000 | 20,000/39,000 |
5.Blow air into the primary air holes on the injector holder.
6.In case any large clumps of dust have now been pushed into the burner repeat steps 3 and 4.
Clean the pilot assembly also. A yellow tip on the pilot flame indicates dust and dirt in the pilot assembly. There is a small pilot air inlet hole about two inches from where the pilot flame comes out of the pilot assembly (see Figure 45). With the unit off, lightly blow air through the air inlet hole. You may blow through a drinking straw if compressed air is not available.
Burner |
|
Tube | Injector Holder |
Primary Air
Inlet Holes
Figure 44 - Injector Holder On Outlet Burner Tube
Ports/Slots
Burner
Tube
Pilot Assembly
Pilot Air
Inlet Hole
Figure 45 - Pilot Inlet Air Hole
LOGS
•If you remove logs for cleaning, refer to Installing Logs, pages 13 through 16, to properly replace logs.
•Replace log(s) if broken or chipped
Type Gas |
| Natural Gas Only |
|
Ignition Piezo | Piezo | Piezo |
|
Manifold Pressure | 3.5" W.C. | 3.5" W.C. | 3.5" W.C. |
Inlet Gas |
|
|
|
Pressure (in. of water) |
|
|
|
Maximum | 10.5" | 10.5" | 10.5" |
Minimum* | 5" | 5" | 5" |
Shipping Weight | 36 lbs. | 38 lbs. | 40 lbs. |
* For the purpose of input adjustment
Dual Burner Biltmore Split Oak Models
| 18" Model | 24" Models | 30" Models |
Btu (Variable) | 16,000/30,000 | 20,000/39,000 | 20,000/39,000 |
Type Gas |
| Natural Gas Only |
|
Ignition Piezo | Piezo | Piezo |
|
Manifold Pressure | 3.5" W.C. | 3.5" W.C. | 3.5" W.C. |
Inlet Gas |
|
|
|
Pressure (in. of water) |
|
|
|
Maximum | 10.5" | 10.5" | 10.5" |
Minimum* | 5" | 5" | 5" |
Shipping Weight | 61 lbs. | 66 lbs. | 70 lbs. |
* For the purpose of input adjustment
Single Burner Seasonal Oak Models
| 18" Model | 24" Model |
Btu (Variable) | 16,000/27,000 | 16,000/31,500 |
Type Gas | Natural Gas Only | |
Ignition Piezo | Piezo |
|
Manifold Pressure | 3.5" W.C. | 3.5" W.C. |
Inlet Gas |
|
|
Pressure (in. of water) |
|
|
Maximum | 10.5" | 10.5" |
Minimum* | 5" | 5" |
Shipping Weight | TBA lbs. | TBA lbs. |
* For the purpose of input adjustment
MAIN BURNER
Periodically inspect all burner flame holes with the heater running. All slotted burner flame holes should be open with yellow flame present. All round burner flame holes should be open with a small blue flame present. Some burner flame holes may become blocked by debris or rust, with no flame present. If so, turn off heater and let cool, Remove blockage, blocked burner flame holes will create soot.
For more
visit www.
.com
