Operating Heater, Lighting Instructions

OPERATING HEATER

FOR YOUR SAFETY READ

BEFORE LIGHTING

WARNING: If you do not fol- low these instructions exactly, a ﬁre or explosion may result causing property damage, per- sonal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the ﬂoor because some gas is heavier than air and will settle on the ﬂoor.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighborʼs phone. Follow the gas supplierʼs instructions.

•If you cannot reach your gas supplier, call the ﬁre department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, donʼt try to repair it, call a qualiﬁed service technician. Force or attempted repair may result in a ﬁre or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualiﬁed service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING

INSTRUCTIONS

1.STOP! Read the safety information above.

2.Make sure equipment shutoff valve is fully open.

3.Turn off any electric power to the appliance if service is to be performed.

4.Turn control knob clockwise to the OFF position.

5.Wait ﬁve minutes to clear out any gas. Then smell for gas, including near the ﬂoor. If you smell gas, STOP! Follow “B” in the safety information above. If you donʼt smell gas, go to the next step.

6.Turn control knob counterclockwise to the PILOT position. Press in control knob for ﬁve (5) seconds.

7.With control knob pressed in, push down and release ignitor button. This will light pilot. The pilot is attached to the front of burner. Note: You may be running this heater for the ﬁrst time after hooking up to gas supply. If so, you may need to press in control knob for 30 seconds or more. This will allow air to bleed from the gas system. If needed, keep pressing ignitor button until pilot lights. If ignitor does not light pilot, refer to Troubleshooting, page 14 or contact a qualiﬁed service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure, page 12.

8.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

•If control knob does not pop up when released, contact a qualiﬁed service person or gas supplier for repairs.

Note: If pilot goes out, repeat steps 4 thru 7. Thermostat models have a safety interlock system. Wait one (1) minute before lighting pilot again.

9.Turn control knob counterclockwise to desired heating level. The main burner should light.

CAUTION: Do not try to ad- just heating levels by using the equipment shutoff valve.

Ignitor Button	Control Knob
	TOILP	LO
	FOF
	HI

Figure 16 - Control Knob In The OFF

Position

Thermocouple

Ignitor Electrode

Pilot Burner

Figure 17 - Pilot

110373-01E

www.desatech.com

RH10PT specifications

Desa RH10PT is a cutting-edge development that showcases the latest advancements in sustainable living and smart technology integration. Situated in an eco-friendly environment, this residential project boasts an impressive array of features designed to enhance the quality of life for its residents while minimizing environmental impact.

One of the main characteristics of Desa RH10PT is its commitment to sustainability. The development incorporates green building practices, utilizing eco-friendly materials and adhering to energy-efficient standards. Solar panels are installed on rooftops, providing residents with renewable energy that reduces electricity costs and carbon footprints. Rainwater harvesting systems are also integrated, allowing for the collection and reuse of water for irrigation and other non-potable uses.

In addition to its sustainability initiatives, Desa RH10PT is designed with smart technology in mind. The residential units are equipped with advanced home automation systems that enable residents to control lighting, heating, and security features remotely via smartphones or tablets. This technology not only enhances convenience but also improves energy management by allowing occupants to monitor and adjust their energy consumption in real time.

Safety is another paramount aspect of Desa RH10PT. The community is secured with state-of-the-art surveillance systems and gated entry points, ensuring a safe living environment for families. Additionally, the design of the neighborhood encourages a sense of community while providing ample green spaces, parks, and recreational facilities. This thoughtful layout promotes outdoor activities and fosters social interactions among residents.

Furthermore, Desa RH10PT emphasizes connectivity and accessibility. The development is strategically located near major transportation hubs, educational institutions, and healthcare facilities, making it an attractive option for families and professionals alike. The integration of walking and biking paths throughout the community encourages healthy lifestyles and reduces reliance on vehicles.

In conclusion, Desa RH10PT represents a modern approach to housing that harmonizes sustainability, technology, and community living. With its innovative features, eco-friendly practices, and smart home technologies, this development is poised to set a benchmark for future residential projects, ultimately shaping the way we think about urban living. Residents are afforded the opportunity to embrace a lifestyle that is not only comfortable but also responsible and forward-thinking, positioning Desa RH10PT as a model for sustainable, modern living in today's world.

Desa RH10PT Operating Heater, For Your Safety Read Before Lighting, Lighting Instructions

Models: RH10PT