OWNER’S MANUAL
INSTALLATION
Continued
13.Install plastic control knob onto output shaft of speed control housing (see Fig- ure 15). Place speed control housing just inside control compartment door in front of stove (see Figure 16).
14.Using two screws provided in blower kit, mount blower speed control hous- ing to mounting tab in left side of lower control compartment (see Figure 16).
15.Check to make sure that the power cord is completely clear of blower wheel and there are no foreign objects in blower wheel.
16.Carefully replace stove top panel. Align holes and replace six screws removed in step 1.
17.Peel off the backing paper and stick the supplied wiring diagram decal on the stove floor bottom as shown in Figure 15.
18.Plug power cord into a convenient
WARNING: ELECTRICAL GROUNDING INSTRUCTIONS This appliance is equipped with a
19.Using speed control knob, turn blower on and check for operation.
20.All remaining parts from blower kit may be discarded.
Blower Speed
Control Housing
Figure16 -InstallingBlowerControlHousing
OPERATING HEATER
FOR YOUR SAFETY
READ BEFORE
LIGHTING
WARNING: If you do not fol- low these instructions exactly, a fire or explosion may result caus- ing property damage, personal injury or loss of life.
A. | This appliance has a pilot which must |
| be lighted by hand. When lighting the |
| pilot, follow these instructions exactly. |
B. BEFORE LIGHTING smell all | |
| around the appliance area for gas. Be |
| sure to smell next to the floor because |
| some gas is heavier than air and will |
| settle on the floor. |
| WHAT TO DO IF YOU SMELL GAS |
| • Do not try to light any appliance. |
| • Do not touch any electric switch; do |
| not use any phone in your building. |
| • Immediately call your gas supplier |
| from a neighbor’s phone. Follow |
| the gas supplier’s instructions. |
| • If you cannot reach your gas sup- |
| plier, call the fire department. |
C. Use only your hand to push in or turn | |
| the gas control knob. Never use tools. |
Power
Cord
Wiring
Diagram
Decal
Control | Speed Control |
Knob | Housing |
WARNING: Never attempt to service heater while it is plugged in, operating, or hot. Burns and electrical shock could result. Only a qualified service person should service or repair heater.
If any of the original wire as supplied with the appliance must be replaced, it must be replaced with 105°C wire or it’s equivalent.
WARNING: Label all wires prior to disconnection when servicing controls. Wiring errors can cause im- proper and dangerous operation. Verify proper opera- tion after servicing.
Variable
|
|
|
| Fan Switch | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
| V.A.C. |
| Off | Black | On | ||||||
|
| Black |
| Motor | |||||||
110/115 |
|
|
|
|
| Blower | |||||
|
|
| Black |
|
|
|
| Black | |||
|
|
| Green |
|
|
|
|
|
|
|
|
|
|
| White |
|
|
|
| White | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
120 Vac. 60 Hz. . 78 Amps |
|
DESA International, Bowling Green, KY |
If the knob will not push in or turn |
by hand, don’t try to repair it, call a |
qualified service technician or gas |
supplier. Force or attempted repair |
may result in a fire or explosion. |
D. Do not use this appliance if any part |
has been under water. Immediately call |
a qualified service technician to inspect |
the appliance and to replace any part |
of the control system and any gas con- |
trol which has been under water. |
Figure 15 - Routing Power Cord
Continued
105683 | 11 | For more information, visit www.desatech.com |
