Desa V36EP-A SERIES, V36EN-A SERIES, VV36EPB(1) SERIES, VV36ENB(1) SERIES Fireplace Installation

Models: V36EP-A SERIES, V36EN-A SERIES, VV36EPB(1) SERIES, VV36ENB(1) SERIES

1 38
Download 38 pages 22.02 Kb
Page 16
Image 16

16

VENTING INSTALLATION INSTRUCTIONS

Parts Lists for Venting Kits and Components

FIREPLACE INSTALLATION

Check Gas Type

Installing Optional Blower Accessory

VENTING INSTALLATION INSTRUCTIONS

Continued

PARTS LISTS FOR VENTING KITS AND

COMPONENTS (CONT.)

Number Description

RF-58-12 Roof Flashing - 6/12 to 12/12 Pitch, Galvanized

VR-58

Vertical Restrictor, Galvanized

S-58

Vinyl Siding Standoff, Galvanized

WS-58

Wall Strap

CS-58

Cathedral Ceiling Support

FP-58

Firestop Plate

SF-58

Stucco Flashing - For use with HTS-5

FIREPLACE INSTALLATION

CHECK GAS TYPE

Use proper gas type for the fireplace unit you are installing. If your gas supply is not correct, do not install fireplace. See retailer where you purchased the fireplace for proper fireplace according to your gas type or to purchase gas conversion kit (see Accessories, page 37).

INSTALLING OPTIONAL BLOWER

ACCESSORY

NOTICE: If installing blower in an existing fireplace with gas connections, shut off gas supply and dis- connect heater from gas supply. Contact a qualified service person to do this.

WARNING: If there is a duplex electrical outlet installed in the right side of the bottom of the fireplace base area, be sure that the electrical power to the outlet is turned off before proceeding with blower installation. Failure to do this may result in serious injury.

Model BK Installation

Follow all instructions provided in the blower accessory kit.

5.Mount speed control box to switch bracket by placing the plastic control shaft forward through the opening in the switch bracket (see Figure 26, page 17).

6.While supporting speed control, secure control shaft with lock nut by pushing and turning lock nut with pliers clockwise until it is tight against front panel. Place control knob provided on shaft.

7.Turn on power to duplex outlet if previously turned off per the warning in column 1.

8.Plug in blower power cord.

a.If your firebox is installed as a freestanding unit with an accessory mantel, determine whether the power cord will exit the left side or the right side of the firebox. Route power cord through exit hole and plug the power cord into a wall receptacle near the firebox.

b.If your firebox installation is recessed and/or pre-wired, plug the power cord into the duplex outlet provided. Refer to your firebox owner’s manual for instructions on wiring the duplex outlet.

CAUTION: Never touch the blower wheel while in operation.

9.Check to make sure that the power cord is completely clear of the blower wheel and that there are no other foreign objects in blower wheel. Turn blower on and check for operation. Turn blower off by turning knob fully counterclockwise before continuing.

10.Peel off the backing paper and stick the supplied wiring dia- gram decal on the firebox bottom approximately 12" in front of the blower (see Figure 27, page 17).

Blower

Location

Lower Firebox

Cavity

Side View

Magnetic Strips

 

Spade Terminals

Exhaust

 

Port

1.Attach the power cord to the blower motor by firmly pushing the two female terminals at the end of the power cord onto the two spade terminals on the blower motor (see Figure 25).

2.Attach green ground wire from power cord to blower housing using screw provided (see Figure 25). Tighten screws securely.

3.Place the blower against the lower rear wall of the firebox outer wrapper with the exhaust port directed upward. The blower will fit inside the back opening and be held in position against the back wall by the magnets (see Figure 25).

4.Be certain that all wire terminals are securely attached to ter- minals on blower motor and that the screw retaining the green ground wire is tight.

Green

Ground Wire

Figure 25 - Blower Model BK

Screw

For..com

111253-01C

Page 16
Image 16
Desa V36EP-A SERIES, V36EN-A SERIES, VV36EPB(1) SERIES, VV36ENB(1) SERIES Fireplace Installation, Check GAS Type

V36EP-A SERIES, V36EN-A SERIES, VV36EPB(1) SERIES, VV36ENB(1) SERIES specifications

The Desa V36EP-A SERIES, V36EN-A SERIES, VV36EPB(1) SERIES, and VV36ENB(1) SERIES represent an innovative lineup of gas vent-free fireplaces designed to enhance the ambiance of any living space while providing efficient heating. These models are particularly noted for their cutting-edge technology and elegant designs, ensuring they blend seamlessly with various interior styles.

The V36EP-A and V36EN-A SERIES are equipped with a highly efficient burner system that provides an impressive heat output without the need for a chimney or venting, making them highly suitable for both new constructions and renovations. These models utilize advanced control systems that allow for easy adjustment of flame height and heat levels, thereby providing users with precise control over their environment.

The VV36EPB(1) SERIES and VV36ENB(1) SERIES take these features a step further with their improved efficiency ratings and attractive detailing. These models feature realistic flame patterns and log sets that mimic the look of traditional wood-burning fireplaces, creating a warm and inviting atmosphere. The ceramic fiber logs not only enhance visual appeal but also contribute to better heat distribution and retention.

One of the standout characteristics of these fireplace series is their incorporation of advanced safety features. Equipped with oxygen depletion sensors and a durable tempered glass front, they ensure safe operation without compromising on performance. The low emissions and reduced environmental impact align with modern energy efficiency standards.

Additionally, the Desa fireplaces come with options for remote controls and programmable thermostats, allowing for hassle-free operation and energy management. Customization options are also abundant, with various finishes and styles available to fit individual preferences and home decor.

In summary, the Desa V36EP-A SERIES, V36EN-A SERIES, VV36EPB(1) SERIES, and VV36ENB(1) SERIES deliver a combination of aesthetic appeal, modern technology, and practical heating solutions. Their vent-free designs make them versatile options for homeowners seeking efficient and stylish heating methods without the need for extensive installation. With their blend of safety, efficiency, and elegance, these fireplace series are poised to redefine comfort and style in home heating.