Desa (V)T32P, (V)T36P SERIES OpTIONAL Hand-Held, Remote Operation, Thermostat Series Model HRC200

OPERATIng fireplace

Continued

OpTIONAL Hand-Held

REMOTE OPERATION

Note: All remote control accessories must be purchased sepa- rately (see Accessories, page 31). Follow instructions included

Thermostat Series Model HRC200

The hand-held remote can be operated using either the manual mode (MANU) or thermostatic mode (AUTO) (see Figure 53). To select Fahrenheit/Centigrade mode display, carefully press the ˚C/˚F mode button with the end of a paper clip or similar blunt object.

Digital Display Shows

Temperature and Settings

with the remote control.

NOTICE: You must light the pilot before using the hand-held remote control unit. See Lighting Instruc- tions, page 23.

After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Adjust flame adjustment knob anywhere between HI and LO. Slide the selector switch to the REMOTE position (see Figure 51). Note: The burner may light if hand-held remote was on when selector switch was last turned off. You can now turn the burner on and off with the hand-held remote control unit.

IMPORTANT: Do not leave the selector switch in the REMOTE

Locks System to Prevent Accidental Ignition

Turns Burners

On or Off

Increases or Decreases Room Temperature in AUTO Mode

			Turns Hand-Held
	AUTO		Remote On or Off
TEMP			and Allows You to
		TEMP
ROOM		SET
			Choose the Manual
LOCK	TEMP	POWER	Setting
MANU	ºC/ºF	AUTO
			Selects
			AUTO Mode
			°C/°F Mode Button

or ON position when the pilot is not lit. This will drain the battery.

Figure 53 - Thermostat Hand-Held Remote Control Unit

Manual Mode HRC200

Blower Control Knob (Optional Accessory)

Variable Control Knob

1.	Press the POWER and LOCK buttons together to turn on
2.	the hand-held remote control.
	Press the MANU button to turn on the fireplace.
3.	Press the POWER and LOCK buttons together to turn off

OFF

REMOTE

OFF

ON

Selector Switch in Remote Position

ON

N
O		L
T		O	I
L		O	H
O
I		F
	P F

Gas Control Knob in ON Position

the fireplace.

Auto (Thermostatic) Mode

1. Press the POWER and LOCK buttons together to turn on the hand-held remote control.

2. Press AUTO button to select this mode.

3. Set the desired room temperature by pressing the TEMP + or - buttons.

Figure 51 - Setting the Selector Switch, Gas Control Knob

and Variable Contorl Knob for Remote Operation

On/Off Series Model HRC100

Hold the control button on the hand-held remote until burner turns on. Hold the control button again until burner turns off (see Figure 52).

To Lock press both buttons on hand-held remote control until light stops flashing. Hand-held remote control is now locked. If the fire is on it will be turned off automatically. In the locked state, the light will not light up when any button is pressed.

To Unlock press both buttons together on hand-held remote control until the light stops flashing. The hand-held remote is now unlocked.

Indicator

LightControl

Button

Figure 52 - On/Off Hand-Held Remote Control Unit HRC100

4. Press the POWER and LOCK buttons together to turn off the fireplace

Note: Do not leave the hand-held remote in the AUTO mode close to the fireplace. The radiant heat from the fireplace will turn off the fireplace. Ideally, place the hand-held remote in the center of the room facing towards the fireplace.

Note: Do not hold the hand-held remote for a long time. Body temperature will affect its operation in the AUTO mode.

Safety Features

When away from home for an extended period of time or as a child safety feature to prevent accidental ignition of the fire- place, the receiver ON/OFF/REMOTE switch should be in the OFF position.

Auto Shutoff Feature

1.If the average room temperature exceeds 82° F (28° C), the hand-held remote control will perform a safety override and shut the fireplace off. This feature is not available in the MANU mode.

2.The receiver continuously receives signals from the hand- held remote to control the room temperature. If the hand- held remote is misplaced, obstructed or for any reason cannot transmit to the receiver, the receiver will shut off the fireplace after 8 minutes.

24 www.desatech.com 108661-01F