OWNER’S MANUAL
PRE-INSTALLATION PREPARATION
GENERAL VENTING
These models are approved for use with
Continued
13"
29"
10 1/4"
8 3/4"
9 1/4" | 41" |
37"
41"
371/2"
411/2"
58"
Simpson
Your fireplace is approved to be vented either through the side wall, or vertically using the following guidelines:
• Only use Comfort Glow or Simpson Dura- Vent GS venting components or kits spe- cifically approved for this fireplace.
•Minimum clearance between vent pipes and combustible materials is 1" (25 mm),
except where stated otherwise.
• Combustible material may be flush with
Nailing Tabs the top front of fireplace with a maxi- mum thichness of 3/4".
• Do not recess venting terminals into a |
wall or siding. |
Note: Where two numbers are given the top number is exclusive to the 37" Fireplace and the bottom number is exclusive to the 41" Fireplace
Figure 6 - Framing Clearances for Corner Installation
|
|
|
|
|
|
|
|
| 1 |
|
|
|
|
|
|
|
|
|
|
| 2 |
|
|
|
|
|
|
|
|
|
|
| 3 |
|
|
|
|
| A |
|
|
|
| Wall | |||
|
|
|
|
|
|
|
|
| 4 |
| |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| B |
|
| 5 |
|
| ||
|
|
|
|
|
|
| C | 6 |
|
| |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| D |
|
|
|
|
|
|
|
|
|
|
| E | 7 |
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| F | G |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| Top of Louver Opening | |||
|
|
|
|
|
|
|
|
| |||
Ref. | Mantel Depth |
| Ref. |
| Mantel from Top |
|
|
| |||
|
|
|
|
|
|
| of Louver Opening |
|
|
| |
|
|
|
|
|
|
|
|
| |||
1 | 14" (356mm) |
| A |
| 16" (406mm) |
|
|
| |||
|
|
|
|
|
|
|
|
| |||
2 | 12" (305mm) |
| B |
| 14" (356mm) |
|
|
| |||
3 | 10" (254mm) |
| C |
| 12" (305mm) |
|
|
| |||
|
|
|
|
|
|
|
|
| |||
4 | 8" (203mm) |
| D |
| 10" (254mm) |
|
|
| |||
|
|
|
|
|
|
|
|
| |||
5 | 6" (152mm) |
| E |
| 8" (203mm) |
|
|
| |||
|
|
|
|
|
|
|
|
| |||
6 | 4" (101mm) |
| F |
| 6" (152mm) |
|
|
| |||
|
|
|
|
|
|
|
|
| |||
7 | 2" (51mm) |
| G |
| 4" (101mm) |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
Figure 7 - Clearances for Combustible Mantels
• Install horizontal venting with a 1/4" rise | |
| for every 12" of run toward the termination. |
• | You may paint the vent terminal with |
| 450ºF (232ºC) |
| ordinate with the exterior finish. |
• | There must not be any obstruction such |
as bushes, garden sheds, fences, decks, or utility buildings within 24" from the front of the termination cap.
•Do not locate termination cap where ex- cessive snow or ice build up may occur. Be sure to clear vent termination area af- ter snow falls to prevent accidental block- age of venting system. When using snow blowers, do not direct snow towards vent termination area.
Location of Vent Termination
When locating vent termination, it is impor- tant to observe the minimum clearances shown in Figure 8, page 6. You will avoid extra framing by positioning your fireplace against an already existing framing mem- ber. The sides of the fireplace may be posi- tioned directly against combustible walls.
*Check with local codes or with the current CAN/CGA B149[.1 or .2] Installation Codes for Canada or the USA Installations follow the current National Fuel Gas Code, ANS Z223.1, also known as NFPA 54.
Continued
104605 | 5 |
