CHDV37N/P AND CHDV41N/P
DIRECT-VENT FIREPLACE (NATURAL/PROPANE/LP)
OPERATING
FIREPLACE
Continued
HAND-HELD REMOTE
OPERATION
NOTICE: You must light the pilot before using the
The thermostat control setting on the remote control unit can be set to any comfort level between HI and LO. The burners will turn on and off automati- cally to maintain the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of the central heating system, etc.
1. After lighting, let pilot flame burn for |
about one minute. Turn gas control |
knob on the control valve to ON posi- |
tion. Turn variable control knob any- |
where between HI and LO. Slide the |
•In auto mode, the room tempera- ture is controlled by the thermo- stat in the
3.Use the STATUS button on the hand- held remote control unit to see the operation mode being used and the temperature setting selected. A red light will come on beside the opera- tion mode being used.
Blower Control Knob | Variable | |
(Optional Accessory) | ||
Control Knob | ||
|
4.To turn the burners off when oper- ating in the manual mode, press the OFF button. If operating in the auto mode, press the MAN button, then press the OFF button. The pilot will remain lit.
IMPORTANT: To turn the pilot off, manually turn the gas control knob on the heater to the OFF position or set selector switch to OFF position.
OPERATING
OPTIONAL BLOWER
ACCESSORY
Locate the blower controls by opening the lower louver panel on the fireplace. Blower controls are located on the left side of the switch bracket to the left just inside the louver panel.
Both the GA3750 manual blower and the CDA3620T
selector switch to the REMOTE posi- |
tion. Note: The burner(s) may light |
if |
on when selector switch was last |
turned off. |
You can now turn the burners on and |
off with the |
OFF
ON
REMOTE
OFF
ON
Selector Switch in Remote Position
N |
| L |
|
O |
| O | I |
T | F | O | H |
O |
|
| |
F |
|
| |
LIP |
|
|
|
Gas Control
Knob in ON
Position
Note for CDA3620T Only: If you are using CDA3620T blower, your fireplace and blower will not turn on and off at the same time. The fireplace may run for several minutes before the blower turns on. After the heater modulates to the pilot position, the blower will continue to run. The blower will shut off after the firebox
unit. |
IMPORTANT: Do not leave the selec- |
tor switch in the REMOTE position |
when the pilot is not lit. This will drain |
the battery. |
IMPORTANT: Be sure to press the |
ON/OFF buttons on the |
Figure 54 - Setting the Selector Switch, Gas Control Knob, and Variable Control Knob for Remote Operation
temperature decreases.
The blower helps distribute heated air from the fireplace. Periodically check the louvers of the firebox and remove any dust, dirt, or other obstructions that will hinder the flow of air.
remote control unit for up to 3 sec- |
onds to assure proper operation. |
2. Select the MAN (manual) or AUTO |
button on the |
trol unit (see Figure 55). |
• In manual mode, turn burners on |
or off by pressing the ON/OFF but- |
tons on the |
trol unit. |
Shows Temperature Setting
Allows Burner(s) to be Turned On and Off with the Hand- Held Remote Unit.
The Heater will Automatically Cycle between Pilot and the Heat Setting that has been Selected.
HI
TEMP
MAN LO ON
AUTO OFF
STATUS
Increases Room Temperature
Decreases Room Temperature
Turns Burners On and Off
Shows Current Operation Mode
Figure 55 - Hand-Held Thermostat Remote Control Unit Selections (GHRCT)
26 | 104605 |
