English

MOTORLIFTING

ENDCAPHANDLE

RAIL SET

MOTOR

SCREW

HOUSING

ADJUSTMENT

 

RAIL LOCK

 

KNOB

 

BEVEL LOCK

 

HANDLE

 

SLIDE

 

STOP

 

BEVEL LATCH

 

LEVER

 

(one each side)

 

FIG. 4

TRIGGER

 

SWITCH

BELT COVER

BLADE

GUARD

DUST SPOUT

THUMBSCREW

BEVEL

SCALE

LOCK DOWN

PIN

BLADE

WRENCH

FENCE

TABLE

 

 

ADJUSTMENT

MITER

MITER LATCH

KNOB

SCALE

OVERRIDE

(ONE EACH SIDE)

 

 

 

 

BENCH MOUNTING HOLES

 

BEVEL

LATCH

PLATES

KERF

PLATE

MITER LATCH

BUTTON

MITER LOCK

HANDLEHAND

INDENTATION

RAILS

GROOVING

STOP

FENCE

5.Return the guard bracket to its original position and firmly tighten the guard bracket screw to hold bracket in place.

WARNING:

•The guard bracket must be returned to its original position and the screw tightened before activating the saw.

•Failure to do so may allow the guard to contact the spinning saw blade resulting in damage to the saw and severe personal injury.

Transporting the Saw

WARNING: To reduce the risk of serious personal injury, turn off the tool and disconnect it from the power source before attempting to move it, change accessories or make any adjustments accept as written in laser adjustment instructions.

WARNING: To reduce the risk of serious personal injury, ALWAYS lock the rail lock knob, miter lock handle, bevel lock handle, lock down pin and fence adjustment knobs before transporting saw.

In order to conveniently carry the miter saw from place to place, a carrying handle has been included on the top of the saw arm and hand indentations in the base, as shown in Figure 4.

Adjustments

WARNING: To reduce the risk of serious personal injury, turn off the tool and disconnect it from the power source before attempting to move it, change accessories or make any adjustments accept as written in laser adjustment instructions.

NOTE: Your miter saw is fully ande ad accurately adjusted at the factory at the time of manufacture. If readjustment due to shipping and handling or any other reason is required, follow the steps below to adjust your saw.

Once made, these adjustments should remain accurate. Take a little time now to follow these directions carefully to maintain the accuracy of which your saw is capable.

MITER SCALE ADJUSTMENT (FIG. 5)

Place a square against the saw’s fence and blade, as shown. (Do not touch the tips of the blade teeth with the square. To do so will cause an inaccurate measurement.) Loosen the miter lock handle and swing the miter arm until the miter latch locks it at the 0 miter position. Do not tighten the lock handle. If the saw blade is not exactly perpendicular to the fence, loosen the four screws that hold the miter scale to the base and move the scale left or right until the blade is perpendicular to the fence, as measured with the square. Retighten the four screws. Pay no attention to the reading of the miter pointer at this time.

7

Page 7 Page 9
Page 8
Image 8
DeWalt DW717 instruction manual Adjustments, Miter Scale Adjustment FIG
Page 7 Page 9

DW717 specifications

The DeWalt DW717 is a powerful and versatile 10-inch dual bevel sliding compound miter saw designed to meet the demands of both professional carpenters and DIY enthusiasts. Known for its durability, precision, and ease of use, the DW717 has become a popular choice for those seeking accurate cuts in a variety of materials.

One of the standout features of the DW717 is its dual bevel capability, which allows users to make precise beveled cuts in both left and right directions. This feature eliminates the need to flip the workpiece, saving valuable time and enhancing overall efficiency. The saw also boasts an impressive crosscut capacity, capable of cutting through wider materials, making it ideal for large-scale projects such as framing and crown molding.

The DW717 is equipped with a powerful 15-amp motor that delivers robust performance for tough cutting tasks. It operates at an impressive no-load speed of 3,800 RPM, ensuring clean and smooth cuts through various materials, including hardwood and softwood. The saw’s motor is designed for high efficiency, providing users with the power needed for continuous operation without overheating.

Another notable technology incorporated into the DW717 is its precision miter system, which offers positive stops at commonly used angles. This feature ensures quick adjustments and accurate cuts, making it easier for users to switch between different angles quickly. The saw includes a miter scale with easy-to-read indicators, allowing for effortless angle setting.

Additionally, the DW717 features an adjustable sliding fence that provides support for larger materials, ensuring stability and precision during cuts. The saw’s lightweight design and built-in carrying handle enhance portability, making it easy to transport to job sites.

Safety features are also a top priority with the DW717. The saw is equipped with a blade guard that protects users from accidental contact with the blade, while the electric brake ensures quick stopping of the blade after the trigger is released.

In summary, the DeWalt DW717 is a well-engineered tool, combining power, precision, and safety for a wide range of cutting tasks. With its dual bevel capabilities, impressive motor, and user-friendly features, it stands out as a reliable choice for both professionals and hobbyists alike. Whether you are tackling framing, molding, or other intricate cuts, the DW717 is built to deliver exceptional performance and results every time.
Top Page Image Contents