4. Choosing a Slot
The DM/V1200BTEPEQ Media board is a full length x1 form factor PCI Express board that requires 25W of power. The following explanation and guidelines are provided to ensure proper configuration of the product.
Power Budgeting is a new feature, introduced in the PCI Express Specification, that provides a mechanism to enable a system to negotiate power consumption requirements for
Per PCI Express Card Electromechanical Specification Revision 1.0a or higher, a x1
The DM/V1200BTEPEQ Media board must be installed in a slot that can be allocated 25W.
If Power Budgeting is not implemented by a vendor's system, the DM/V1200BTEPEQ Media board must be plugged into a x4 or higher slot with the P10 jumper in position
If Power Budgeting is implemented by a vendor's system, the DM/V1200BTEPEQ Media board can be plugged into a x1 slot but the P10 jumper must be in position pins
WARNING! Installing the DM/V1200BTEPEQ Media board in a x1 slot with the P10 jumper in position
If the DM/V1200BTEPEQ Media board will be connected to other telephony boards via a CT Bus cable, you should install the boards to minimize unused connectors on the CT Bus cable (in addition to ensuring that the power requirements are met):
■Install boards in adjacent slots whenever possible.
■If the DM/V1200BTEPEQ Media board will be connected to one or more PCI boards, use the PCI Express slot(s) closest to the PCI slots.
5. Installing the Board
WARNING! Unplug the equipment before performing the procedures described here. Failure to disconnect the power before you open the chassis can result in personal injury. Ensure that the system is disconnected from its power source and from all telecommunications links, networks, or modem lines whenever the chassis cover is removed. Do not operate the system with the cover removed.
CAUTION: To avoid possible damage to the board, remove power from the computer before beginning installation. Observe proper
To install the DM/V1200BTEPEQ Media board, perform the following steps:
1.Turn off all power to the system and disconnect the system’s power cords.
2.Remove the computer’s cover.
3.Choose an empty PCI Express expansion slot and remove the slot’s retaining screw and access cover plate.
4.Insert the board’s edge connector into the bus slot, and apply firm pressure to the top edge of the board until the board is fully seated in the edge connector.
5.Reinstall the retaining screw.
6.Repeat Step 3 through Step 5 for any additional boards you are installing
7.Connect the telephony boards together with a CT Bus cable of the appropriate size (not included). If possible, use a cable assembly that matches the number of boards in your system. If the cable has more than one unused connector, install the cable so that all the unused connectors are at one end of the cable.
CT Bus
ColoredCable Stripe
(Pin 1)
Note:
Your CT Bus cable may have a different number of connectors (drops).
8.Replace the computer’s cover.
9.Reconnect the computer’s power cord.
Remove |
| |
Cover | PCI Express | |
Plate | ||
Board | ||
Computer | ||
| ||
Chassis |
| |
| PCI Express | |
| Slots | |
| PCI Slots |
6.Connecting to External Equipment
Each
The following figure illustrates the pinout of the RJ- 48C jack.
7. After Installing the Board
The DM/V1200BTEPEQ Media board requires the use of a Dialogic®System Software version that specifically supports it.
If this is the first Dialogic® telecom board you have installed in your system, you will need to install an appropriate version of the Dialogic® System Software and configure the software for the specific board(s) you are using. Refer to the installation and configuration documentation that accompanies the release for instructions.
If you are installing the DM/V1200BTEPEQ Media board in a system that already has the Dialogic® System Software installed, you should verify that your installed software version supports the board. If not, you will need to obtain and install a Service
Pinout for | Network Interface |
PCI Express Board's Bracket | Cable Connector |
1 |
|
2 |
|
3 |
|
4 |
|
5 |
|
6 |
|
7 |
|
8 |
|
1 RCV_RING | Pin 1 |
|
2RCV_TIP
3Chassis Ground
4XMIT_RING
5XMIT_TIP
6Chassis Ground
7Chassis Ground
8Chassis Ground
Update that does support the DM/V1200BTEPEQ Media board before configuring the system for the newly installed board(s).
Please refer to the Release Update document for your release version (on the Dialogic Telecom Support Resources web page) for
For technical specifications and product information go to: http://www.dialogic.com/products.htm.
8. Removing the Board
Removal of the DM/V1200BTEPEQ Media board is essentially the reverse of the installation procedure:
1.Observe
2.Disconnect the telephony cables.
3.Remove the computer’s power cord.
4.Remove the computer’s cover.
5.Disconnect the CT Bus cable (if applicable).
6.Remove and set aside the board’s retaining screw.
7.Remove the board and place it in static- protective packaging.
Removal of the board is a straightforward process. Remove the board using the reverse of the procedure described in the Installing the Board section.
9.Warranty and Return Information
Warranty Period
For specific warranty information for this board, refer to the Warranty section of the Products page, located at this URL: http://www.dialogic.com/ warranties/.
Contacting Technical Support
Dialogic provides technical support for its products through a network of value added distributors who are trained to answer technical questions on installing and configuring Dialogic® products. If you are unsure how to contact your support channel, please call Dialogic in the United States at
Outside the United States please refer to http:// www.dialogic.com/support/contact to obtain local contact information. Dialogic also provides direct support via Dialogic® Pro™ Services agreements. For more details of direct support from Dialogic please refer to:http://www.dialogic.com/support/ Dialogic Pro
Returning a Product
To return a board for warranty repair or any other returns, please refer to the following: http:// www.dialogic.com/support/hwfaults.
10. Sales Assistance
If you have a sales question, please contact your local Sales Representative or the Regional Sales Office for your area. Address, telephone and fax numbers, are available at the Dialogic website located at: http://www.dialogic.com/contact.htm.
To purchase Dialogic® products, please refer to the following website to locate the appropriate supplier: http://www.dialogic.com/purchase.htm.
All contents of this document are furnished for informational use only and are subject to change without notice and do not represent a commitment on the part of Dialogic Corporation or its subsidiaries (“Dialogic”). Reasonable effort is made to ensure the accuracy of the information contained in the document. However, Dialogic does not warrant the accuracy of this information and cannot accept responsibility for errors, inaccuracies or omissions that may be contained in this document.
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH DIALOGIC® PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED AGREEMENT BETWEEN YOU AND DIALOGIC, DIALOGIC ASSUMES NO LIABILITY WHATSOEVER, AND DIALOGIC DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT OF A THIRD PARTY.
Dialogic products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility applications.
It is possible that the use or implementation of any one of the concepts, applications, or ideas described in this document, in marketing collateral produced by or on web pages maintained by Dialogic may infringe one or more patents or other intellectual property rights owned by third parties. Dialogic does not provide any intellectual property licenses with the sale of Dialogic products other than a license to use such product in accordance with intellectual property owned or validly licensed by Dialogic and no such licenses are provided except pursuant to a signed agreement with Dialogic. More detailed information about such intellectual property is available from Dialogic’s legal department at 9800 Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada H4M 2V9. Dialogic encourages all users of its products to procure all necessary intellectual property licenses required to implement any concepts or applications and does not condone or encourage any intellectual property infringement and disclaims any responsibility related thereto. These intellectual property licenses may differ from country to country and it is the responsibility of those who develop the concepts or applications to be aware of and comply with different national license requirements.
Dialogic, Diva, Eicon, Eicon Networks, Eiconcard, Dialogic Pro and SIPcontrol, among others, are either registered trademarks or trademarks of Dialogic. Dialogic's trademarks may be used publicly only with permission from Dialogic. Such permission may only be granted by Dialogic’s legal department at 9800 Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada H4M 2V9. Any authorized use of Dialogic's trademarks will be subject to full respect of the trademark guidelines published by Dialogic from time to time and any use of Dialogic’s trademarks requires proper acknowledgement. The names of actual companies and products mentioned herein are the trademarks of their respective owners.
