Manuals / Diamond Systems / Computer Equipment / Computer Hardware

Diamond Systems Low-Power PC/104 CPU Board With ZFx86 Processor Table Of Contents Continued, 12.1

Models: Low-Power PC/104 CPU Board With ZFx86 Processor PR-Z16-LC-ST

1 38

Page 3

TABLE OF CONTENTS (CONTINUED)


12.	I/O PANEL BOARD		28
12.1		Description	28
12.2		Panel Board I/O Connectors	29
12.3		Panel Board Cables	29
12.4		Panel Board Hardware	29
12.5		Panel Board Power Connections	30
12.6		Speaker and Miscellaneous Connector	31
12.7		Watchdog Timer	32
12.8		Installation	32
13.	FLASH DISK PROGRAMMER BOARD		33
14.	I/O CABLES		34
15.	VGA ACCESSORY BOARD		35
16.	MOUNTING PROMETHEUS-LC ON A BASEBOARD		36
17.	PC/104 MECHANICAL DRAWING		38

Prometheus-LC CPU User Manual V1.0

Page 3

Image 3

Contents

PROMETHEUS-LC Model PR-Z16-LC-ST Low-Power PC/104 CPU Board With ZFx86 ProcessorSYSTEM FEATURES TABLE OF CONTENTSFEATURES JUMPER CONFIGURATIONFLASH DISK PROGRAMMER BOARD TABLE OF CONTENTS CONTINUEDVGA ACCESSORY BOARD I/O PANEL BOARDPROMETHEUS-LC Low-Power PC/104 CPU Board with ZFx86 Processor 1. DESCRIPTION2. FEATURES System Features System FeaturesProcessor Section J13 Not present 3. PROMETHEUS-LC BOARD DRAWINGJ4 Not present J14 Not presentCable “B” 4.1 Main I/O Connector - J34. I/O HEADERS Cable “A”Connector Part Numbers Notes on J3 Signals4.2 Input Power - J11 4.4 USB - J5 4.3 Output Power - J124.5 Auxiliary Serial Port Connector - J15 Do not use both J15 and the corresponding pins on J3 simultaneously4.6 Watchdog/Failsafe Features - J6 4.8 IDE Drive - J8 4.7 Floppy Drive - J7View from Top of Board 4.9 PC/104 Bus ConnectorsJ2 PC/104 16-bit bus connector J1 PC/104 8-bit bus connector5.1 System Configuration - J10 5. JUMPER CONFIGURATION5.2 Watchdog Timer & System Recovery - J6 Device 6. SYSTEM FEATURES6.1 System Resources 6.2 CPU Chip SelectsThere are three possible configurations for console redirection 6.3 Console Redirection to a Serial Port6.4 Watchdog Timer 6.6 Flash Memory 6.5 Failsafe Mode / BIOS Recovery6.7 Backup Battery 6.8 System Reset7.1 BIOS Settings 7. BIOS FEATURESPrometheus-LC COM1 end 7.2 BIOS Download / Recoveryzftrm.exe loadbios.com prm1.rom PC Serial Port End DB-9Initial Setup 8. DISK-ON-BOARD FLASH FILE STORAGEOperating System Formatting Known Limitations Life Cycle Management and CalculationsLifetime in days = number of file writes / file writes per day 9. SYSTEM I/O 9.1 Serial Ports9.2 Parallel Port 10.1 Installing an OS From a Floppy Drive onto a Flashdisk Module 10.NOTES ON OPERATING SYSTEMS AND BOOTING PROCEDURES10.2 Installing an OS from a Hard Disk onto a Flashdisk Module 11.4 Power Supply 11.1 Installation11.2 Configuration 11.3 Using the Flashdisk with Another IDE Drive12.1 Description 12. I/O PANEL BOARDLocation 12.2 Panel Board I/O ConnectorsPanel Board Top Side / External Use I/O Connectors Panel Board Bottom Side / Internal Use I/O ConnectorsJ12 pinout to/from DC/DC power supply 12.5 Panel Board Power ConnectionsJ3 Pinout J13 pinout user connection 12.6 Speaker and Miscellaneous ConnectorJ9 Pinout 12.8 Installation 12.7 Watchdog TimerACC-IDEEXT FlashDisk Programmer Board 13.FLASH DISK PROGRAMMER BOARDCable Kit C-PRZ-KIT 14.I/O CABLESPhoto No Cable NoSignal 15.VGA ACCESSORY BOARDPL5 Signal J25 SignalManufacturer Part No Connector on Board16.MOUNTING PROMETHEUS-LC ON A BASEBOARD ManufacturerPage Prometheus-LC CPU User ManualPrometheus-LC CPU User Manual 17.PC/104 MECHANICAL DRAWING

TABLE OF CONTENTS (CONTINUED)

I/O PANEL BOARD

12.1

Description

12.2

Panel Board I/O Connectors

12.3

Panel Board Cables

12.4

Panel Board Hardware

12.5

Panel Board Power Connections

12.6

Speaker and Miscellaneous Connector

12.7

Watchdog Timer

12.8

Installation

FLASH DISK PROGRAMMER BOARD

I/O CABLES

VGA ACCESSORY BOARD

MOUNTING PROMETHEUS-LC ON A BASEBOARD

PC/104 MECHANICAL DRAWING