Dimension One Spas 01510-1030E Rev A specification

Installing Power Supply in Equipment Compartment

Export Sonic Immersion System Dealer Installation Guide

Installing Power Supply in Equipment Compartment

1.Turn the power supply so that you can see the Voltage Selector Switch, see Figure 28, and place the switch in the correct position (115V for UL and CSA spas or 240V for CE spas) for your location.

1.Voltage Switch

Figure 28. Voltage Switch on Back of Power Supply

2.Locate two #8 x ½” (1.27 cm) Pan head screws (P/N 01011-

38)in the power supply kit. The power supply has two holes for attaching it to the wall of the equipment compartment, Figure 29. Locate the hole in the upper right corner of the power supply. Use electric screwdriver to secure the power supply. Now use the remaining screw to secure the left bottom corner of the power supply.

28

Image 32

Dimension One Spas 01510-1030E Rev A manual Installing Power Supply in Equipment Compartment

Contents

Page Page OWNER’S MANUAL Table of ContentsDEALER INSTALLATION Export Sonic Immersion System Features of the Sonic Immersion Using the CD Player This section intended for use by authorized dealer personnel only Dealer InstallationExport Sonic Immersion System Dealer Installation Guide Overview of the Installation Getting Ready To StartRequired Tools Table 1 Sonic Immersion System Ready Spas Table 2 Required Tools Tape masking, electrical, duct, or packaging ½ in 12.7 mm width Parts List Medium Size Needle Nose Pliers Wire Stripper Utility KnifeStapler and Staples Straight Edge Safety Glasses 5/16” 7.94 mm Nut Driver or wrench Six inch 15.24 cm square Number Table 3 Parts ListDescription assembly Power supplyStereo 01564-03 Removing Panels Remove Equipment Compartment Panel Figure 1. Top Side Control Figure 2. Equipment Compartment Panel Screws Remove the Sub Woofer Compartment Panel Sub-Woofer Installation Locator Table 4 Model ListAurora II and Chairman Location of Installation Figure 3. Equipment Compartment Panel Screws Caliente HP, Triad II, Aurora HP, and Triad1. Use the screwdriver to remove the spa panel screws, Figure The number of screws to be removed will depend on the model of spa Figure 5. Cutting Rectangle Installing the Sub Woofer CompartmentFigure 4. Removing EnviroTect Sheeting Figure 6. Sub-Woofer Plug The photograph Figure 5 may not look like your spa, refer to Table1. Sub-Woofer Plug The plug may not come out in one piece Figure 7. Removing Plug Figure 8. Electrical Conduit Figure 9. Conduit After Trimming1. Electrical Conduit Before Trimming 1. Electrical Conduit After Trimming Figure 10. Drilling Hole for Cables Figure 12. Properly Installed Sub-Woofer Figure 11. Edge of Frame1. Bottom Edge of Frame 9. A properly positioned sub woofer compartment is shown in Figure Pre Wiring from Equipment Compartment to Sub Woofer Compartment Figure 13. Attaching to Frame Figure 14. Fish Tape in Equipment Compartment Figure 15. Attaching Cables and Harness to Fish Tape Figure 16. Applying Lubricant to Cables Figure 17. Cables in Sub-Woofer Figure 18. Stripping Wires Figure 19. Connecting Wires for Power Input Figure 20. Connecting Wires to Speaker Output Figure 22. Connecting Wires to Channel 1 and Figure 21. Terminals and Controls Figure 23. Setting Controls Installation of Power SupplyPre-Wire Power Supply Figure 24. Connector Wire Configuration Figure 25. Connecting Wires to 120 Volt Supply on Power Supply Figure 27. Connecting Wire to Amplifier Terminals on Power Supply Figure 26. Connecting Wires to Stereo and 12 V SupplyTerminals on Power Supply Installing Power Supply in Equipment Compartment Figure 28. Voltage Switch on Back of Power Supply 1. Location of Upper and Lower Screw Holes Figure 29. Location of Attachment Holes on Power SupplyFigure 30. Connecting Harness to Power Supply Wiring the Power Supply Figure 31. Inserting Wires in Lower Control Box Table 5 Pin Connectors Figure 32. Removing Nut from Ground TerminalBoard Description Pin Connections Determining Location of CD Weather Cover Figure 33. Determining Location of CD Weather Cover Cutting Panel Hole for CD Player Door Assembly 1. Bottom of Panel 2. Panel Lay Face Up 3. Top of Panel Figure 34. Measuring Vertical DistanceFigure 35. Measuring Horizontal Distance Figure 37. Connecting Marks Figure 36. Aligning Template Figure 38. Hole Locations Figure 39. Panel Cutout Installation of CD Player Door and Bezel Figure 40. Bezel and Door Assembly Installation of Panel and CD Player Figure 41. Door Assembly Installed Figure 42. Door Assembly Ready for CD Player Connection Installing the Satellite Speakers Figure 43. Typical Satellite Speaker Installation Figure 44. Protective Caps in Place \ 1. Caps in Place Installing the Satellite Speaker Wires Figure 45. Speaker Wires Attached Figure 46. Installing Speaker Wires Figure 47. Satellite Speaker Wires in Sub-Woofer Compartment Figure 48. Connecting Satellite Speaker Wires to Amplifier Figure 49. Speaker Wires to Satellite Speakers Figure 50. Completed Speaker Installation Figure 51. Securing Amplifier to the Frame Complete the InstallationSecuring the Amplifier Page Page Part No. 01510-1030E Rev A  2002 Dimension One Spas