Installation of Power Supply | Dimension One Spas 01510-1030E Rev A

Figure 23. Setting Controls

Export Sonic Immersion System Dealer Installation Guide

Figure 23. Setting Controls

12.Set BASS BOOST CH1 and CH 2 to the MIN position.

13.Set HIGH PASS CH 1 and CH 2 to the 200 HZ positions.

14.Set CH 1 to HP position and CH 2 to LP position.

Installation of Power Supply

Pre-Wire Power Supply

Locate the power supply kit that contains the power supply (P/N 01564-0) and a 12-pin connector (P/N 01564-19) containing wires in the following configuration, see Figure 24.

25

Image 29

Dimension One Spas 01510-1030E Rev A manual Installation of Power Supply, Pre-Wire Power Supply, Setting Controls

Contents

Page Page OWNER’S MANUAL Table of ContentsDEALER INSTALLATION Export Sonic Immersion System Using the CD Player Features of the Sonic Immersion This section intended for use by authorized dealer personnel only Dealer InstallationExport Sonic Immersion System Dealer Installation Guide Getting Ready To Start Overview of the InstallationRequired Tools Table 1 Sonic Immersion System Ready Spas Tape masking, electrical, duct, or packaging ½ in 12.7 mm width Table 2 Required Tools Medium Size Needle Nose Pliers Wire Stripper Utility Knife Parts ListStapler and Staples Straight Edge Safety Glasses 5/16” 7.94 mm Nut Driver or wrench Six inch 15.24 cm square Number Table 3 Parts ListDescription Power supply assemblyStereo 01564-03 Remove Equipment Compartment Panel Removing Panels Figure 2. Equipment Compartment Panel Screws Figure 1. Top Side Control Remove the Sub Woofer Compartment Panel Table 4 Model List Sub-Woofer Installation LocatorAurora II and Chairman Location of Installation Caliente HP, Triad II, Aurora HP, and Triad Figure 3. Equipment Compartment Panel Screws1. Use the screwdriver to remove the spa panel screws, Figure The number of screws to be removed will depend on the model of spa Figure 5. Cutting Rectangle Installing the Sub Woofer CompartmentFigure 4. Removing EnviroTect Sheeting The photograph Figure 5 may not look like your spa, refer to Table Figure 6. Sub-Woofer Plug1. Sub-Woofer Plug The plug may not come out in one piece Figure 7. Removing Plug Figure 9. Conduit After Trimming Figure 8. Electrical Conduit1. Electrical Conduit Before Trimming 1. Electrical Conduit After Trimming Figure 10. Drilling Hole for Cables Figure 11. Edge of Frame Figure 12. Properly Installed Sub-Woofer1. Bottom Edge of Frame 9. A properly positioned sub woofer compartment is shown in Figure Figure 13. Attaching to Frame Pre Wiring from Equipment Compartment to Sub Woofer Compartment Figure 15. Attaching Cables and Harness to Fish Tape Figure 14. Fish Tape in Equipment Compartment Figure 17. Cables in Sub-Woofer Figure 16. Applying Lubricant to Cables Figure 18. Stripping Wires Figure 20. Connecting Wires to Speaker Output Figure 19. Connecting Wires for Power Input Figure 21. Terminals and Controls Figure 22. Connecting Wires to Channel 1 and Figure 23. Setting Controls Installation of Power SupplyPre-Wire Power Supply Figure 25. Connecting Wires to 120 Volt Supply on Power Supply Figure 24. Connector Wire Configuration Figure 27. Connecting Wire to Amplifier Terminals on Power Supply Figure 26. Connecting Wires to Stereo and 12 V SupplyTerminals on Power Supply Figure 28. Voltage Switch on Back of Power Supply Installing Power Supply in Equipment Compartment 1. Location of Upper and Lower Screw Holes Figure 29. Location of Attachment Holes on Power SupplyFigure 30. Connecting Harness to Power Supply Figure 31. Inserting Wires in Lower Control Box Wiring the Power Supply Figure 32. Removing Nut from Ground Terminal Table 5 Pin ConnectorsBoard Description Pin Connections Figure 33. Determining Location of CD Weather Cover Determining Location of CD Weather Cover Cutting Panel Hole for CD Player Door Assembly 1. Bottom of Panel 2. Panel Lay Face Up 3. Top of Panel Figure 34. Measuring Vertical DistanceFigure 35. Measuring Horizontal Distance Figure 36. Aligning Template Figure 37. Connecting Marks Figure 39. Panel Cutout Figure 38. Hole Locations Figure 40. Bezel and Door Assembly Installation of CD Player Door and Bezel Figure 41. Door Assembly Installed Installation of Panel and CD Player Figure 42. Door Assembly Ready for CD Player Connection Figure 43. Typical Satellite Speaker Installation Installing the Satellite Speakers \ 1. Caps in Place Figure 44. Protective Caps in Place Figure 45. Speaker Wires Attached Installing the Satellite Speaker Wires Figure 46. Installing Speaker Wires Figure 47. Satellite Speaker Wires in Sub-Woofer Compartment Figure 49. Speaker Wires to Satellite Speakers Figure 48. Connecting Satellite Speaker Wires to Amplifier Figure 50. Completed Speaker Installation Figure 51. Securing Amplifier to the Frame Complete the InstallationSecuring the Amplifier Page Page Part No. 01510-1030E Rev A  2002 Dimension One Spas