Removing Panels | Dimension One Spas 01510-1030E Rev A specification

Removing Panels

Export Sonic Immersion System Dealer Installation Guide

Cable Ty Mount

10

01200-005

Removing Panels

In order to install the system up to three panels must be removed from the spa: the equipment compartment panel, the panel where the sub woofer is installed, and the panel where the Satellite Speakers are to be installed.

Remove Equipment Compartment Panel

Possible Electrical Shock Hazard

Warning

1.Turn off the main spa circuit breaker located in the disconnect box or house panel.

2.Verify that all power has been turned off before continuing installation.

Refer to the Spa Service Manual to determine how to confirm that all power to the spa has been turned off.

Note

3.Locate the spa’s Main Top Side Control, Figure 1.

8

Image 12

Dimension One Spas 01510-1030E Rev A manual Removing Panels, Remove Equipment Compartment Panel

Contents

Page Page Table of Contents DEALER INSTALLATIONOWNER’S MANUAL Export Sonic Immersion System Features of the Sonic Immersion Using the CD Player Dealer Installation Export Sonic Immersion System Dealer Installation GuideThis section intended for use by authorized dealer personnel only Overview of the Installation Getting Ready To StartRequired Tools Table 1 Sonic Immersion System Ready Spas Table 2 Required Tools Tape masking, electrical, duct, or packaging ½ in 12.7 mm width Parts List Medium Size Needle Nose Pliers Wire Stripper Utility KnifeStapler and Staples Straight Edge Safety Glasses 5/16” 7.94 mm Nut Driver or wrench Six inch 15.24 cm square Table 3 Parts List DescriptionNumber assembly Power supplyStereo 01564-03 Removing Panels Remove Equipment Compartment Panel Figure 1. Top Side Control Figure 2. Equipment Compartment Panel Screws Remove the Sub Woofer Compartment Panel Sub-Woofer Installation Locator Table 4 Model ListAurora II and Chairman Location of Installation Figure 3. Equipment Compartment Panel Screws Caliente HP, Triad II, Aurora HP, and Triad1. Use the screwdriver to remove the spa panel screws, Figure The number of screws to be removed will depend on the model of spa Installing the Sub Woofer Compartment Figure 4. Removing EnviroTect SheetingFigure 5. Cutting Rectangle Figure 6. Sub-Woofer Plug The photograph Figure 5 may not look like your spa, refer to Table1. Sub-Woofer Plug The plug may not come out in one piece Figure 7. Removing Plug Figure 8. Electrical Conduit Figure 9. Conduit After Trimming1. Electrical Conduit Before Trimming 1. Electrical Conduit After Trimming Figure 10. Drilling Hole for Cables Figure 12. Properly Installed Sub-Woofer Figure 11. Edge of Frame1. Bottom Edge of Frame 9. A properly positioned sub woofer compartment is shown in Figure Pre Wiring from Equipment Compartment to Sub Woofer Compartment Figure 13. Attaching to Frame Figure 14. Fish Tape in Equipment Compartment Figure 15. Attaching Cables and Harness to Fish Tape Figure 16. Applying Lubricant to Cables Figure 17. Cables in Sub-Woofer Figure 18. Stripping Wires Figure 19. Connecting Wires for Power Input Figure 20. Connecting Wires to Speaker Output Figure 22. Connecting Wires to Channel 1 and Figure 21. Terminals and Controls Installation of Power Supply Pre-Wire Power SupplyFigure 23. Setting Controls Figure 24. Connector Wire Configuration Figure 25. Connecting Wires to 120 Volt Supply on Power Supply Figure 26. Connecting Wires to Stereo and 12 V Supply Terminals on Power SupplyFigure 27. Connecting Wire to Amplifier Terminals on Power Supply Installing Power Supply in Equipment Compartment Figure 28. Voltage Switch on Back of Power Supply Figure 29. Location of Attachment Holes on Power Supply Figure 30. Connecting Harness to Power Supply1. Location of Upper and Lower Screw Holes Wiring the Power Supply Figure 31. Inserting Wires in Lower Control Box Table 5 Pin Connectors Figure 32. Removing Nut from Ground TerminalBoard Description Pin Connections Determining Location of CD Weather Cover Figure 33. Determining Location of CD Weather Cover Cutting Panel Hole for CD Player Door Assembly Figure 34. Measuring Vertical Distance Figure 35. Measuring Horizontal Distance1. Bottom of Panel 2. Panel Lay Face Up 3. Top of Panel Figure 37. Connecting Marks Figure 36. Aligning Template Figure 38. Hole Locations Figure 39. Panel Cutout Installation of CD Player Door and Bezel Figure 40. Bezel and Door Assembly Installation of Panel and CD Player Figure 41. Door Assembly Installed Figure 42. Door Assembly Ready for CD Player Connection Installing the Satellite Speakers Figure 43. Typical Satellite Speaker Installation Figure 44. Protective Caps in Place \ 1. Caps in Place Installing the Satellite Speaker Wires Figure 45. Speaker Wires Attached Figure 46. Installing Speaker Wires Figure 47. Satellite Speaker Wires in Sub-Woofer Compartment Figure 48. Connecting Satellite Speaker Wires to Amplifier Figure 49. Speaker Wires to Satellite Speakers Figure 50. Completed Speaker Installation Complete the Installation Securing the AmplifierFigure 51. Securing Amplifier to the Frame Page Page Part No. 01510-1030E Rev A  2002 Dimension One Spas