Dimension One Spas 01510-1030E Rev A specs

Figure 42. Door Assembly Ready for CD Player

Export Sonic Immersion System Dealer Installation Guide

Figure 42. Door Assembly Ready for CD Player

Connection

3.Reattach panel to spa.

4.Connect antenna, main harness and amplifier to CD player as described in CD player owner’s manual. Connect power supply cable (long branch of main harness) to power supply connector on CD player. Connect Channel 1 preamp stereo cables (RCA cable) to FRONT connectors on the CD player and the Channel 2 cables to the REAR connectors on the CD player.

Note

Connecting the preamp cables (RCA cables) in this manner will allow the front and rear faders to increase or decrease the sound level of the sub- woofer or satellite speakers.

5.Then slide CD player into sleeve and lock in position.

39

Image 43

Dimension One Spas 01510-1030E Rev A manual Door Assembly Ready for CD Player Connection

Contents

Page Page DEALER INSTALLATION Table of ContentsOWNER’S MANUAL Export Sonic Immersion System Using the CD Player Features of the Sonic Immersion Export Sonic Immersion System Dealer Installation Guide Dealer InstallationThis section intended for use by authorized dealer personnel only Table 1 Sonic Immersion System Ready Spas Overview of the InstallationGetting Ready To Start Required Tools Tape masking, electrical, duct, or packaging ½ in 12.7 mm width Table 2 Required Tools 5/16” 7.94 mm Nut Driver or wrench Six inch 15.24 cm square Parts ListMedium Size Needle Nose Pliers Wire Stripper Utility Knife Stapler and Staples Straight Edge Safety Glasses Description Table 3 Parts ListNumber 01564-03 assemblyPower supply Stereo Remove Equipment Compartment Panel Removing Panels Figure 2. Equipment Compartment Panel Screws Figure 1. Top Side Control Remove the Sub Woofer Compartment Panel Location of Installation Sub-Woofer Installation LocatorTable 4 Model List Aurora II and Chairman The number of screws to be removed will depend on the model of spa Figure 3. Equipment Compartment Panel ScrewsCaliente HP, Triad II, Aurora HP, and Triad 1. Use the screwdriver to remove the spa panel screws, Figure Figure 4. Removing EnviroTect Sheeting Installing the Sub Woofer CompartmentFigure 5. Cutting Rectangle The plug may not come out in one piece Figure 6. Sub-Woofer PlugThe photograph Figure 5 may not look like your spa, refer to Table 1. Sub-Woofer Plug Figure 7. Removing Plug 1. Electrical Conduit After Trimming Figure 8. Electrical ConduitFigure 9. Conduit After Trimming 1. Electrical Conduit Before Trimming Figure 10. Drilling Hole for Cables 9. A properly positioned sub woofer compartment is shown in Figure Figure 12. Properly Installed Sub-WooferFigure 11. Edge of Frame 1. Bottom Edge of Frame Figure 13. Attaching to Frame Pre Wiring from Equipment Compartment to Sub Woofer Compartment Figure 15. Attaching Cables and Harness to Fish Tape Figure 14. Fish Tape in Equipment Compartment Figure 17. Cables in Sub-Woofer Figure 16. Applying Lubricant to Cables Figure 18. Stripping Wires Figure 20. Connecting Wires to Speaker Output Figure 19. Connecting Wires for Power Input Figure 21. Terminals and Controls Figure 22. Connecting Wires to Channel 1 and Pre-Wire Power Supply Installation of Power SupplyFigure 23. Setting Controls Figure 25. Connecting Wires to 120 Volt Supply on Power Supply Figure 24. Connector Wire Configuration Terminals on Power Supply Figure 26. Connecting Wires to Stereo and 12 V SupplyFigure 27. Connecting Wire to Amplifier Terminals on Power Supply Figure 28. Voltage Switch on Back of Power Supply Installing Power Supply in Equipment Compartment Figure 30. Connecting Harness to Power Supply Figure 29. Location of Attachment Holes on Power Supply1. Location of Upper and Lower Screw Holes Figure 31. Inserting Wires in Lower Control Box Wiring the Power Supply Pin Connections Table 5 Pin ConnectorsFigure 32. Removing Nut from Ground Terminal Board Description Figure 33. Determining Location of CD Weather Cover Determining Location of CD Weather Cover Cutting Panel Hole for CD Player Door Assembly Figure 35. Measuring Horizontal Distance Figure 34. Measuring Vertical Distance1. Bottom of Panel 2. Panel Lay Face Up 3. Top of Panel Figure 36. Aligning Template Figure 37. Connecting Marks Figure 39. Panel Cutout Figure 38. Hole Locations Figure 40. Bezel and Door Assembly Installation of CD Player Door and Bezel Figure 41. Door Assembly Installed Installation of Panel and CD Player Figure 42. Door Assembly Ready for CD Player Connection Figure 43. Typical Satellite Speaker Installation Installing the Satellite Speakers \ 1. Caps in Place Figure 44. Protective Caps in Place Figure 45. Speaker Wires Attached Installing the Satellite Speaker Wires Figure 46. Installing Speaker Wires Figure 47. Satellite Speaker Wires in Sub-Woofer Compartment Figure 49. Speaker Wires to Satellite Speakers Figure 48. Connecting Satellite Speaker Wires to Amplifier Figure 50. Completed Speaker Installation Securing the Amplifier Complete the InstallationFigure 51. Securing Amplifier to the Frame Page Page Part No. 01510-1030E Rev A  2002 Dimension One Spas