220 Volt Installation/Operating Instructions
LCD Lift Video Projector Lift
These Installation/Operating Instructions are available in the official language of the country where you purchase the product. Please contact your distributor to request a copy.
Vous pourriez demander les instructions d’installation et d’opération traduises dans la langue officielle du pays ou vous achetez le produit. Veuillez demander à votre distributeur.
Die Gebrauchsanweisung für Installation und Konstruktion sind in der offiziellen Sprache des Landes, indem Sie das Produkt gekauft haben, vorhanden. Fragen Sie die jeweilige
Caution
➀Read instructions completely before proceeding.
➁Follow instructions carefully. Installation contrary to instructions
invalidates warranty.
➂Do not obstruct operation of doors or universal (fl at) closure with fi ngers
or any object. Serious injury or damage could result.
➃It is not uncommon to overheat the motor during initial installation when
setting limits. The motor is thermally protected and will stop working temporarily. DO NOT physically pull the unit down when this occurs. Once it has cooled to a safe temperature, it will begin operating again.
➄LCD Lift is designed to accommodate ceiling suspended equipment. Equipment should not be allowed to rest on doors during operation.
➅Unit must be installed level (use a carpenter’s level).
➆Perform
➇ Unit operates on
Note: Unit has been thoroughly inspected and tested at factory and found to be operating properly prior to shipment.
Planning
➀Based on screen location and projector specifi cations, determine proper position for projector installation.
➁Confi rm that there is adequate space available above the ceiling: 49 cm for LCD Lift A; 62 cm for LCD Lift B.
NOTE: Add an additional 2 cm of ceiling space if using ceiling closure panel.
➂Arrange to provide service access to electrical control box.
➄Use the switch to move the traveling pan up and down. Removal of the access panel will allow the observation of this movement. The unit will stop automatically when it reaches the fully up or fully down position.
➅Cycle the unit in both directions until you are satisfi ed the unit is operating properly. If for any reason the unit does not seem to operate properly, call
Draper, Inc.
➆If the unit has been ordered with the remote control option, again verify operation of the unit by use of the hand held transmitter. If for any reason the unit does not seem to operate properly, call Draper, Inc.,
Do not proceed with installation.
➇If the unit is operating satisfactorily, remove and discard the temporary plug.
➈Disconnect the switch at the terminal board (terminals #1, #3, and #7). Do not discard this switch. It is to be used as the wall switch.
➉Replace the cover on the electrical box and proceed with the installation, referring to instructions supplied.
Hanging Unit
The LCD Lift may be installed in a variety of ways. Typically, it is recessed above the ceiling and supported by four ½" (12.7 mm) threaded mounting rods. The bottom of the LCD Lift should be recessed approximately 4 cm above the fi nished ceiling. The threaded rods should pass through mounting holes supplied in each corner and be secured by nuts above and below (see Fig. 1). The unit should then be guy wired or blocked to prevent swinging. All installations should observe the following guidelines:
➀Installer must ensure that all fasteners and supports are of adequate strength to securely support LCD Lift and projector.
Caution: DO NOT hang from, "ride" or pull down on the unit. This could create a failure and cause damage and/or injury.
➁Fastening methods must be suitable for mounting surface, and anchored so vibrations or abusive pulling will not weaken installation.
➂Unit should be level, with weight shared more or less equally by all four threaded mounting rods.
➃Bottom of unit must be unobstructed after installation. 31 cm minimum clearance is required below LCD Lift A; 37 cm below LCD Lift B.
As Soon as LCD Lift Arrives:
➀Open carton and inspect for damage.
➁ Locate the following parts: | Continued on next page | |
A. The unit itself | ||
| ||
B. Bomb bay doors or optional ceiling closure | LCD Lift Dimensions | |
C. Controls |
| |
D. Optional SMS Low Profi le Mount with Universal Bracket |
|
➂Follow
|
| A |
|
|
|
|
| A |
|
| C |
|
|
|
| C | |
This LCD Lift was extensively tested and in perfect condition when it left our |
|
|
|
|
|
| ||
plant. To make sure that it arrived in the same condition, please use the following |
|
|
|
|
|
|
|
|
procedure to test the unit prior to installation. Draper does not accept back charges |
|
|
| For 12.7 mm threaded rod |
| |||
for labor. Make sure that this unit is operating satisfactorily before installation. | B | D |
| (supplied by others) |
|
| ||
Danger! The traveling pan can exert over 30 kg of force. Do not insert any |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| |
body parts or other objects into this unit while power is connected. |
|
|
|
|
|
|
|
|
➀ Remove the unit from the outer carton. |
|
| 14.3 mm dia. |
|
|
|
| |
➁ Remove the cover of the electrical box. |
|
| mounting holes |
|
|
|
| |
➂ |
|
|
|
|
|
|
|
|
and plug the unit into a 220V AC outlet. Caution: Do not touch any |
|
|
|
|
|
|
|
|
exposed wires while the unit is plugged in. |
|
|
|
|
|
|
|
|
➃ Inside the electrical box you will fi nd that a temporary plug has been |
|
|
|
|
|
|
|
|
connected to the terminal board. Extend this plug from the box. |
|
|
|
|
|
|
|
|
Replace the electrical box cover so that the cover is held loosely (so as not |
|
|
|
|
|
|
|
|
to crush the wires) in place. |
|
|
|
|
|
|
|
|
|
|
| Bomb bay door assembly standard. |
|
| |||
|
|
| Flat ceiling closure panel available. |
|
| |||
|
|
| A | B | C | D | Travel | Lift |
|
|
| (cm) | (cm) (cm) | (cm) | (cm) | Capacity | |
|
| LCD Lift A | 60 | 45 | 46 | 28 | 29 | 30 kgs |
|
| LCD Lift B | 73 | 57 | 58 | 41 | 42 | 30 kgs |
Figure 1
|
|
|
|
|
|
| If you encounter difficulties installing or servicing your LCD Lift, call |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| your dealer or Draper, Inc., Spiceland, Ind., (765) |
|
|
|
|
|
|
| |
Copyright © 2008 Draper Inc. Form LCDLift220V_Inst08 | Printed in U.S.A. | (765) |