Maintenance, Cutting Large Sheets, Service | Dremel 670 manual

5716 Dremel 2.625x4.25 6/18/02 10:31 AM Page 18

CUTTING LARGE SHEETS

Large sheets and long boards sag or bend, depending on support. If you attempt to cut without leveling and properly supporting the piece, the blade will tend to bind, causing KICKBACK and extra load on the rotary tool. (Fig. 1)

Figure1

Kickback

Support the panel or board close to the cut, as shown in (Fig. 2). Be sure that you cut through the sheet or board only and not the table or work bench. The two-by-fours used to raise and support the work should be positioned so that the broadest sides support the work and rest on the table or bench. Do not support the work with the narrow sides as this is an unsteady arrangement. If the sheet or board to be cut is too large for a table or work bench, use the supporting two-by- fours on the floor and secure.

Figure 2

Feed Direction

Maintenance

SERVICE

Preventive maintenance ! WARNING performed by unauthorized personnel may result in misplacing of internal components which could cause serious hazard. We recommend that all tool service be

performed by a Dremel Service Facility.

TOOL LUBRICATION

Your saw attachment has been properly lubricated and is ready to use.

18

19

Image 10

Dremel 670 manual Maintenance, Cutting Large Sheets, Performed by a Dremel Service Facility, Tool Lubrication

Contents

Dremel 2.625x4.25 6/18/02 1029 AM Keep hands Power Tool Safety RulesSafety Rules for Mini Saw Attachment Cutting area Causes and Operator Prevention of Kickback Symbols Name Functional Description and Specifications Assembly Mini SAW Attachment Installation Blade Assembly Install the drive adapter on the motor shaft and tightenTo prevent damage to tool Dremel 2.625x4.25 6/18/02 1031 AM Directional Guide Operating InstructionsTypes of Cuts Feed direction for the rotary tool is right to left only Performed by a Dremel Service Facility MaintenanceService Cutting Large Sheets Certain cleaning agents CleaningCare of Blades Garder CES Instructions Garder les mains éloignées Causes ET Prévention DU Recul PAR L’UTILISATEUR Recul Symboles Nom Assemblage Installation D’INSTRUMENTS SUR LA MINI-SCIEDescription fonctionnelle et spécifications Capacité maximum Lame 1-1/4 po 31,8 mm Alésage central Dremel 2.625x4.25 6/18/02 1035 AM Pour éviter d’endommager Assemblage DE LA Lame’outil, ne pas trop serrer Dremel 2.625x4.25 6/18/02 1035 AM Genres DE Coupes Mode d’emploiGuide Directionnel LA Coupe DE Grandes Feuilles Lubrification DE L’OUTIL De l’ammoniaque Nettoyage’ENTRETIEN DES Lames Instrucciones. No seguir las Guarde Estas InstruccionesLea y entienda todas las Mantenga las manos lejos Dremel 2.625x4.25 6/18/02 1037 AM Contragolpe Símbolos Nombre Ensamble Descripción funcional y especificacionesPara uso con los modelos Dremel 275, 285, 395, 398 y Instalacion DEL Acople DE Minisierra Herramienta Paso 2. Remueva el collarín Daño a la Ensamble DE LA Cuchilla Dremel 2.625x4.25 6/18/02 1037 AM Guia Direccional Instrucciones de operaciónTipos DE Corte Corte DE Hojas Grandes Lubricacion DE LA Herramienta MantenimientoServicio Contregolpe Para evitar LimpiezaCuidado DE LAS Cuchillas Dremel 2.625x4.25 6/18/02 1037 AM 2610914192