230V | CAUTION |
| ||
870 WATTS |
| |||
RISK OF ELECTRIC SHOCK | ||||
|
| DO NOT OPEN |
| |
MAINS FUSE | CIRCUIT T TO |
| POWER REMOTE | |
T10A/L/250V | CHASSIS SWITCH | POWER | ||
GROUNDED | + | |||
|
|
UNGROUNDED | SEE OPERATING MANUAL! |
CHANNEL B |
|
|
|
|
|
|
|
|
|
|
|
| CHANNEL A | ||||||
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
INPUTS |
|
|
|
|
| INPUT |
|
|
| INPUTS | |||||||||
|
| + |
|
|
| ROUTING |
| + |
|
| |||||||||
|
|
|
|
| DUAL |
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
| 0 dB |
|
|
|
|
| 0 dB |
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
| LEVEL | PARALLEL |
| LEVEL |
|
|
|
|
CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE |
| WARNING: TO REDUCE THE RISK OF FIRE |
REPLACE WITH SAME TYPE AND VALUE FUSE INDICATED. |
| OR ELECTRIC SHOCK, DO NOT EXPOSE THIS |
ATTENTION:REMPLACER PAR UN FUSIBLE DE MEME TYPE |
| APPLIANCE TO RAIN OR MOISTURE. |
COMME INDIQUE. |
| AVIS: RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR. |
AUDIO TRANSFORMER OUTPUTS |
| |||||
B | LOW IMPEDANCE | A |
| |||
+ 100V |
| BRIDGED+ | 100V + |
| ||
+ 25V +70V |
| 1200W/8 |
| 70V+ 25V+ | ||
B | DUAL | A | ||||
|
|
| ||||
| + | 600W | + |
|
| |
|
| 4 |
|
|
| |
100 70 | 0 DIRECT OUTPUTS 0 | 70 100 | OUTPUT WIRING MUST BE CLASS 1 | |||
| ISOLATED OUTPUTS |
| ||||
|
|
|
+24V ON
0V OFF
DPA 4260 121715 |
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
MADE IN GERMANY
BRIDGED MODE
NORMAL BRIDGED
S+
PIN 1: SHIELD
PIN 2: a, +
PIN 3: b, -
+
Inputs INPUT CHANNEL A&B
With an input sensitivity of 775 mV = 0 dBu and an input impedance of 20 k ohms, the electronically balanced inputs – INPUT CHANNEL A&B
–are meant for the connection of control amplifiers, audio controllers, mixing consoles, etc.
Peripheral pieces of audio equipment are either connected via the XLR- type input connectors or using the
The
In case the controlling device does not supply balanced output connec- tors, it is also possible to configure the connectors for unbalanced ope- ration. Therefore, the common ground (pin 1) has to be connected to the
(–)input (pin 3). The audio signal is now solely fed through the (+) input (pin 2).
So, to be able to entirely make use of all the advantages the electroni- cally balanced input stage offers – like the suppression of humming and interference noise – it is beneficial to
Instructions On How To Install NRS 90208 Extension Kits
•
•
•
•
•
•
•
•
unplug the power amplifier from the mains
detach all screws holding the cover plate of the appliance lift and remove the cover plate
disconnect the
remove the printed board assembly 81340/1 and unsolder the resistors R106 … R109
attach insulators to the input transformers according to the corespondent marks on the printed board assembly
19