22

 

Problem

 

Solution

 

 

 

 

 

Double images or

 

Use a highly directional antenna or cable TV.

 

“ghosts”

 

 

 

 

 

 

 

Good picture but no

 

• Make sure that the sound is not muted.

 

sound

 

Press MUTE to cancel.

 

 

 

• Make sure that the stereo mode is set to

 

 

 

Stereo or Mono.

 

 

 

 

 

Audio noise

 

Problems may occur if infrared

 

 

 

communications equipment (such as

 

 

 

infrared cordless phones) are used near the

 

 

 

TV. Move the infrared communications

 

 

 

equipment away from the TV until the noise

 

 

 

is eliminated.

 

 

 

 

 

Remote control

 

 

 

 

 

 

 

The remote control

 

• Aim the remote control at the remote

 

does not work

 

control sensor.

 

 

 

• Operate within about 15 feet of the TV, or

 

 

 

reduce the light in the room.

 

 

 

• Clear the path of the infrared beam.

 

 

 

• The batteries may be weak. Replace the

 

 

 

batteries.

 

 

 

• Make sure that the batteries are inserted

 

 

 

correctly.

 

 

 

 

Specifications

 

 

 

 

Type

LCD TV

 

 

 

 

Panel

22” TFT LCD

 

 

 

 

TV system

NTSC-M, ATSC

 

 

 

 

Receiving channels

VHF 2-13, UHF 14-69, CATV 1-125, CADTV 1-135,

 

 

DTV 2-69

 

Audio multiplex

BTSC system

 

 

 

 

Power requirement

AC 120 V, 60 Hz

 

 

 

 

Power consumption

48 W

 

 

 

 

Dimensions

20.24 × 16.14 × 7.09 inches

 

(W × H × D)

(514 × 410 × 180 mm)

 

 

 

 

Weight

11.5 lbs (5.2 kg)

 

 

 

 

Input terminals

Composite video/audio L/R (1)

 

 

S-Video (1)

 

 

Component video/audio L/R (1)

 

 

HDMI interface (1)

 

 

VGA/Audio (1)

 

 

Antenna (1)

 

 

 

 

Output terminals

Headphone jack (1)

 

 

 

 

Control

RS-232 (1)

 

 

 

 

Specifications are subject to change without notice. Weight and dimensions shown are approximate.

Legal notices

FCC Part 15

This device complies with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Specifications

This equipment has been tested and found to comply within the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced technician for help.

FCC warning

Changes or modifications not expressly approved by the party responsible for compliance with the FCC Rules could void the user’s authority to operate this equipment.